參數資料
型號: MAX2986CXV
廠商: Maxim Integrated Products, Inc.
英文描述: Single Channel M-LVDS Type-1 Receiver 8-SON
中文描述: 集成電力線數字收發器
文件頁數: 8/28頁
文件大?。?/td> 349K
代理商: MAX2986CXV
M
Integrated Powerline Digital Transceiver
8
_______________________________________________________________________________________
Table 1. Upper Layer Interface-Selection Pin Settings
INTERFACE
MII
rMII
FIFO
GPIO[3]
0
0
0
GPIO[6]
0
1
1
GPIO[4]
1
0
1
MIIRXDV are high), the external host must wait until the
completion of reception and the deassertion of MIICRS
before starting a transmission. When sending two con-
secutive frames, the minimum time the external host
needs to wait is the one-frame transfer time plus an
interframe gap.
Note:
For information such as signal timing characteris-
tics and electrical characteristics, refer to the IEEE
802.3u.
Note:
The MII signals MIICOL and MIITXER are not
used, as the powerline networking device is able to
detect and manage all transmission failures. The sig-
nals MIITXCLK and MIIRXCLK have the same source
and are referred to as MIICLK in this document.
In MII mode, the data is transferred synchronously with
a 2.5MHz/25MHz clock. Data transmission in MII is in
nibble format so the data transmission rate is
10Mbps/100Mbps.
In rMII mode, the data is transferred synchronously with
a 5MHz/50MHz clock. Data transmission in MII is in
2-bit format so the data transmission rate is
10Mbps/100Mbps.
In FIFO mode, data is read and written in byte format
on each positive edge of BUFRD and BUFWR. The only
limitation in this mode is that BUFRD and BUFWR must
be low for at least three pulses of MIICLK to be consid-
ered a valid signal.
The upper layer interface can be selected according to
the settings shown in Table 1.
MII Interface Signals
Table 2 describes the signals that provide data, status,
and control to and from the MAX2986 in MII mode.
Table 2. MII Signal Description
NAME
LINES
I/O
DESCRIPTION
MIIDAT
[3:0]
4
I
Transmit Data.
Data are transferred to the MAX2986 from the external MAC across these four lines,
one nibble at a time, synchronous to MIICLK.
MIITXEN
1
I
Transmit Enable.
Provides the framing for the Ethernet packet from the Ethernet MAC. This signal
indicates to the MAX2986 that valid data is present on MIIDAT[3:0] and must be sampled using
MIICLK.
MIICRS
1
O
Carrier Sense.
Logic-high indicates to the external host that traffic is present on the powerline and the
host must wait until the signal goes invalid before sending additional data. When a packet is being
transmitted, MIICRS is held high.
MIIDAT
[7:4]
4
O
Receive Data.
Data are transferred from the MAX2986 to the external MAC across these four lines, one
nibble at a time, synchronous to MIICLK. The MAX2986 properly formats the frame so the Ethernet
MAC is presented with the expected preamble plus the start frame delimiter (SFD).
MIIRXDV
1
O
Receive Data Valid.
Logic-high indicates that the incoming data on the MIIDAT pins are valid.
MIIRXER
1
O
Receive Error.
Logic-high indicates to the external MAC that the MAX2986 detected a decoding error
in the receive stream.
MIICLK
MANAGEMENT DATA UNIT
MIIMDC
1
I
Reference Clock.
A 2.5MHz (25MHz) clock in 10Mbps (100Mbps) as reference clock.
1
I
Management Data Clock.
A 2.5MHz noncontinuous clock reference for the MIIMDIO signal.
MIIMDIO
1
I/O
Management Data Input/Output.
A bidirectional signal that carries the data for the management data
interface.
相關PDF資料
PDF描述
MAX3030EESE 【15kV ESD-Protected, 3.3V Quad RS-422 Transmitters
MAX3031EESE 【15kV ESD-Protected, 3.3V Quad RS-422 Transmitters
MAX3032EESE 【15kV ESD-Protected, 3.3V Quad RS-422 Transmitters
MAX3033EESE 【15kV ESD-Protected, 3.3V Quad RS-422 Transmitters
MAX3030 【15kV ESD-Protected, 3.3V Quad RS-422 Transmitters
相關代理商/技術參數
參數描述
MAX2986DVKIT 制造商:Maxim Integrated Products 功能描述:PLDC (HOMEPLUG 1.0) BASEBAND W/O MAC - Rail/Tube
MAX2986EVB 功能描述:電信線路管理 IC Integrated Powerline Digital Transceiver RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
MAX2986EVKIT 功能描述:網絡開發工具 PLDC (HOMEPLUG 1.0) BASEBAND W/O MAC RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
MAX2986EVKIT# 功能描述:網絡開發工具 MAX2986 EVAL KIT+ RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
MAX2986EVKIT+ 制造商:Maxim Integrated Products 功能描述:EVAL KIT - Bulk