參數資料
型號: MAX2986CXV
廠商: Maxim Integrated Products, Inc.
英文描述: Single Channel M-LVDS Type-1 Receiver 8-SON
中文描述: 集成電力線數字收發器
文件頁數: 13/28頁
文件大?。?/td> 349K
代理商: MAX2986CXV
M
Integrated Powerline Digital Transceiver
______________________________________________________________________________________
13
rMII Signal Timing
rMII transmit and receive timing are the same as for MII,
except that the data are sent and received in 2-bit
format and MIICRS is removed.
FIFO Interface Signals
Table 6 describes signals that provide data, status, and
control to and from the MAX2986 in buffering (FIFO)
mode. The FIFO buffering interface is operated in half-
duplex mode. MIIRXDV is never asserted at the same
time as MIITXEN, but it is able to start transmission
while receive is in progress. It is highly recommended
to give reception a higher priority to avoid data loss.
On transmit, the MAX2986 asserts MIICRS after MIITXEN
is asserted, and drops it after MIITXEN is deasserted
and when the MAX2986 is ready to get another packet.
When MIICRS falls, it can be asserted again if there is
another packet to send.
Transmissions are modulated onto the wire as soon as
the transfer begins, as the interface fills the MAX2986
buffer faster than data needs to be made available to
the modulator. When a packet arrives at the MAX2986,
it attempts to gain access to the channel. Since this
may not happen before the entire packet is transferred
across the interface, the MAX2986 buffers at least one
Ethernet packet to perform this rate adaptation.
On receive; when the MAX2986 anticipates that it will
have a packet demodulated, it raises MIIRXDV to iden-
tify the upper layer that a packet is ready to transmit.
MIIRXDV drops when the last byte is transmitted.
Receive direction transfers have priority over the transmit
direction to ensure that the buffer empties faster than
packets arrive. The minimum receive time is one Tx frame
plus an IFG.
Table 6. FIFO Signal Description
NAME
DATA
LINES
I/O
DESCRIPTION
MIIDAT[7:0]
8
I/O
Transmit/Receive Data.
Data are transferred to/from the MAX2986 from/to the external MAC
across this bidirectional port, one byte at a time.
MIITXEN
1
I
Transmit Enable [Active High].
This signal indicates to the MAX2986 that the transmission has
started, and that data on MIIDAT should be sampled using
BUFWR
. MIITXEN remains high to
the end of the session.
MIICRS
1
O
Transmit In Progress [Active High].
When asserted high, MIICRS indicates to the external
host that outgoing traffic is present on the powerline and the host should wait until the signal
goes low before sending additional data.
BUFWR
1
I
Write [Active Low].
Inputs a write signal to the MAX2986 from the external MAC, writing the
present data on MIIDAT pins into the interface buffer on each positive edge.
MIIRXDV
1
O
Receive Data Valid [Active High].
When asserted high, MIIRXDV indicates that the incoming
data on the MIIDAT pins are valid.
MIIRXER
1
O
Receive Error [Active High].
When asserted high, MIIRXER indicates to the external MAC that
an error has occurred during the frame reception.
BUFRD
1
I
Read [Active Low].
Inputs a read signal to the MAX2986 from the external MAC, reading the
data from the MIIDAT pins of the MAX2986 on each positive edge.
BUFCS
MIICLK
1
1
I
I
Chip Select [Active Low].
When asserted low, it enables the chip.
Reference Clock.
Used for sampling
BUFWR
and
BUFRD
.
相關PDF資料
PDF描述
MAX3030EESE 【15kV ESD-Protected, 3.3V Quad RS-422 Transmitters
MAX3031EESE 【15kV ESD-Protected, 3.3V Quad RS-422 Transmitters
MAX3032EESE 【15kV ESD-Protected, 3.3V Quad RS-422 Transmitters
MAX3033EESE 【15kV ESD-Protected, 3.3V Quad RS-422 Transmitters
MAX3030 【15kV ESD-Protected, 3.3V Quad RS-422 Transmitters
相關代理商/技術參數
參數描述
MAX2986DVKIT 制造商:Maxim Integrated Products 功能描述:PLDC (HOMEPLUG 1.0) BASEBAND W/O MAC - Rail/Tube
MAX2986EVB 功能描述:電信線路管理 IC Integrated Powerline Digital Transceiver RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
MAX2986EVKIT 功能描述:網絡開發工具 PLDC (HOMEPLUG 1.0) BASEBAND W/O MAC RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
MAX2986EVKIT# 功能描述:網絡開發工具 MAX2986 EVAL KIT+ RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
MAX2986EVKIT+ 制造商:Maxim Integrated Products 功能描述:EVAL KIT - Bulk