- 您現在的位置：買賣IC網 > PDF目錄45022 > M306H3MC-XXXFP 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP116 PDF資料下載
參數資料
| 型號： | M306H3MC-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP116 |
| 封裝： | 20 X 20 MM, 0.65 MM PITCH, PLASTIC, LQFP-116 |
| 文件頁數： | 98/135頁 |
| 文件大?。?/td> | 2583K |
| 代理商： | M306H3MC-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁當前第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁
Rev.1.00
2004.03.23
page 65 of 320
M306H3MC-XXXFP/FCFP
2.7.6 Interrupt Sequence
An interrupt sequence — what are performed over a period from the instant an interrupt is accepted to the
instant the interrupt routine is executed — is described here.
If an interrupt occurs during execution of an instruction, the processor determines its priority when the
execution of the instruction is completed, and transfers control to the interrupt sequence from the next
cycle. If an interrupt occurs during execution of either the SMOVB, SMOVF, SSTR or RMPA instruction,
the processor temporarily suspends the instruction being executed, and transfers control to the interrupt
sequence.
The CPU behavior during the interrupt sequence is described below. Figure 2.7.4 shows time required for
executing the interrupt sequence.
(1) The CPU gets interrupt information (interrupt number and interrupt request priority level) by reading the
address 0000016. Then it clears the IR bit for the corresponding interrupt to “0” (interrupt not re-
quested).
(2) The FLG register immediately before entering the interrupt sequence is saved to the CPU’s internal
temporary register(Note 1).
(3) The I, D and U flags in the FLG register become as follows:
The I flag is cleared to “0” (interrupts disabled).
The D flag is cleared to “0” (single-step interrupt disabled).
The U flag is cleared to “0” (ISP selected).
However, the U flag does not change state if an INT instruction for software interrupt Nos. 32 to 63 is
executed.
(4) The CPU’s internal temporary register (Note 1) is saved to the stack.
(5) The PC is saved to the stack.
(6) The interrupt priority level of the accepted interrupt is set in the IPL.
(7) The start address of the relevant interrupt routine set in the interrupt vector is stored in the PC.
After the interrupt sequence is completed, the processor resumes executing instructions from the start
address of the interrupt routine.
Note: This register cannot be used by user.
Indeterminate (Note 1)
1
2
34
56
78
9
10
11
12
13
1415
16
1718
Indeterminate (Note 1)
SP-2
contents
SP-4
contents
vec
contents
vec+2
contents
Interrupt
information
Address
000016
Indeterminate (Note 1)
SP-2
SP-4
vec
vec+2
PC
CPU clock
Address bus
Data bus
WR
RD
Note 1 : The indeterminate state depends on the instruction queue buffer. A read cycle occurs when
the instruction queue buffer is ready to accept instructions.
Note 2 : The WR signal timing shown here is for the case where the stack is located in the internal RAM.
(Note 2)
Figure 2.7.4. Time Required for Executing Interrupt Sequence
相關PDF資料 |
PDF描述 |
|---|---|
| M306H3FCFP | 16-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP116 |
| M306H5MG-XXXFP | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP116 |
| M306H5MG-XXXFP | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP116 |
| M306H5FGFP | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP116 |
| M306N4FGVFP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M306H5FGFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SNGLE-CHIP 16-BIT CMOS MICROCOMPUTER with DATA ACQUISITION CONTROLLER |
| M306H5FGFP#U0 | 功能描述:IC M16C/6H MCU FLASH 116LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:M16C™ M16C/60 標準包裝:160 系列:S08 核心處理器:S08 芯體尺寸:8-位 速度:40MHz 連通性:I²C，LIN，SCI，SPI 外圍設備:LCD，LVD，POR，PWM，WDT 輸入/輸出數:53 程序存儲器容量:32KB（32K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1.9K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 12x12b 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:64-LQFP 包裝:托盤 |
| M306H5MC-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SNGLE-CHIP 16-BIT CMOS MICROCOMPUTER with DATA ACQUISITION CONTROLLER |
| M306H5MG-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SNGLE-CHIP 16-BIT CMOS MICROCOMPUTER with DATA ACQUISITION CONTROLLER |
| M306H7FGFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with DATA ACQUISITION CONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。