參數資料
型號： LPC2919
廠商： NXP Semiconductors N.V.
元件分類： 32位微控制器
英文描述： ARM9 microcontroller with CAN and LIN
中文描述： 具有CAN和LIN的ARM9微控制器
文件頁數： 16/68頁
文件大?。?/td> 384K
代理商： LPC2919
DRAFTDRAFTDRAFTDRAFTDRAFTDRAFTD
LPC2917_19_1
NXP B.V. 2007. All rights reserved.
Preliminary data sheet
Rev. 1.01 — 15 November 2007
16 of 68
NXP Semiconductors
LPC2917/19
ARM9 microcontroller with CAN and LIN
Both buffer lines are invalidated after:
Initialization
Configuration-register access
Data-latch reading
Index-sector reading
The modes of operation are listed in
Table 8
.
Table 8.
Synchronous timing
No buffer line
Single buffer line
8.1.3
Flash memory controller pin description
The flash memory controller has no external pins. However, the flash can be programmed
via the JTAG pins, see
Section 7.1.3
.
8.1.4
Flash memory controller clock description
The flash memory controller is clocked by CLK_SYS_FMC, see
Section 7.2.2
.
8.1.5
Flash layout
The ARM processor can program the flash for ISP (In-System Programming) and IAP (In-
Application Programming). Note that the flash always has to be programmed by ‘flash
words’ of 128 bits (four 32-bit AHB bus words, hence 16 bytes).
The flash memory is organized into eight ‘small’ sectors of 8 kB each and up to 11 ‘large’
sectors of 64 kB each. The number of large sectors depends on the device type. A sector
must be erased before data can be written to it. The flash memory also has sector-wise
protection. Writing occurs per page which consists of 4096 bits (32 flash words). A small
sector contains 16 pages; a large sector contains 128 pages.
Table 9
gives an overview of the flash-sector base addresses.
Table 9.
Sector number
0
1
2
Flash read modes
for single (non-linear) reads; one flash-word read per word read
default mode of operation; most recently read flash word is kept until
another flash word is required
Asynchronous timing
No buffer line
Single buffer line
one flash-word read per word read
most recently read flash word is kept until another flash word is
required
on a buffer miss a flash read is done, followed by at most one
speculative read; optimized for execution of code with small loops
(less than eight words) from flash
most recently used flash word is copied into second buffer line; next
flash-word read is started; highest performance for linear reads
Dual buffer line, single
speculative
Dual buffer line, always
speculative
Flash sector overview
Sector size (kB)
8
8
8
Sector base address
0000 0000h
0000 2000h
0000 4000h
相關PDF資料
PDF描述
LPC3180 16/32-bit ARM microcontroller; hardware floating-point coprocessor, USB On-The-Go, and SDRAM memory interface
LPC61W26X Microcontroller
LPC61W49X Microcontroller
LPC660AIMX Voltage-Feedback Operational Amplifier
LPC660IMX Voltage-Feedback Operational Amplifier
相關代理商/技術參數
參數描述
LPC2919/01 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ARM9 microcontroller with CAN and LIN
LPC2919FBD144 制造商:NXP Semiconductors 功能描述:IC MCU 32BIT ARM968 SMD LQFP144
LPC2919FBD144,551 功能描述:ARM微控制器 - MCU ARM968 768K FL/48K RAM LIN 2.0 RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2919FBD144/01 制造商:NXP Semiconductors 功能描述:MCU, 32BIT, ARM968E-S, 125MHZ, LQFP-144 制造商:NXP Semiconductors 功能描述:MCU, 32BIT, ARM968E-S, 125MHZ, LQFP-144, Controller Family/Series:LPC2900, Core Size:32bit, No. of I/O's:108, Supply Voltage Min:1.71V, Supply Voltage Max:1.89V, Digital IC Case Style:LQFP, No. of Pins:144, Program Memory Size:768KB,
LPC2919FBD144/01/ 制造商:NXP Semiconductors 功能描述:MCU ARM9 144LQFP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*