參數資料
型號： LMK04001BISQE/NOPB
廠商： National Semiconductor
文件頁數： 19/65頁
文件大小： 0K
描述： IC CLOCK COND 1.5GHZ W/PLL 48LLP
標準包裝： 1
系列： PowerWise®
類型： 時鐘調節器
PLL： 是
輸入： LVCMOS
輸出： LVCMOS，2VPECL，LVPECL
電路數： 1
比率 - 輸入:輸出： 2:7
差分 - 輸入:輸出： 是/是
頻率 - 最大： 1.57GHz
除法器/乘法器： 是/是
電源電壓： 3.15 V ~ 3.45 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 48-WFQFN 裸露焊盤
供應商設備封裝： 48-LLP（7x7）
包裝： 標準包裝
產品目錄頁面： 1275 (CN2011-ZH PDF)
其它名稱： LMK04001BISQEDKR
SNOSAZ8J – SEPTEMBER 2008 – REVISED SEPTEMBER 2011
The Phase Frequency Detector in PLL2 then compares the divided (R Divider 2) reference signal from the PLL2
OSCin port with the divided (N Divider 2 and VCO Divider) output of the internal VCO. The bandwidth of the
external loop filter for PLL2 should be designed to be wide enough to take advantage of the low in-band phase
noise of PLL2 and the low high offset phase noise of the internal VCO. The VCO output is passed through a
common VCO divider block and placed on a distribution path for the clock distribution section. It is also routed to
the PLL2_N counter. Each clock output channel allows the user to select a path with a programmable divider
block, a phase synchronization circuit, a programmable delay, and LVDS/LVPECL/2VPECL/LVCMOS compatible
output buffers.
Phase Detector 1 (PD1)
Phase Detector 1 in PLL1 (PD1) can operate up to 40 MHz. Since a narrow loop bandwidth should be used for
PLL1, the need to operate at high phase detector rate to lower the in-band phase noise becomes unnecessary.
Phase Detector 2 (PD2)
Phase Detector 2 in PLL2 (PD2) supports a maximum comparison rate of 100 MHz, though the actual maximum
frequency at the input port (PLL2 OSCin/OSCin*) is 250 MHz. Operating at highest possible phase detector rate
will ensure low in-band phase noise for PLL2 which in turn produces lower total jitter, as the in-band phase noise
from the reference input and PLL are proportional to N2.
PLL2 Frequency Doubler
The PLL2 reference input at the OSCin port may be optionally routed through a frequency doubler function rather
than through the PLL2_R counter. The maximum phase comparison frequency of the PLL2 phase detector is 100
MHz, so the input to the frequency doubler is limited to a maximum of 50 MHz. The frequency doubler feature
allows the phase comparison frequency to be increased when a relative low frequency oscillator is driving the
OSCin port. By doubling the PLL2 phase comparison frequency, the in-band PLL2 noise is reduced by about 3
dB.
Inputs / Outputs
PLL1 Reference Inputs (CLKin0 / CLKin0*, CLKin1 / CLKin1*)
The reference clock inputs for PLL1 may be selected from either CLKin0 and CLKin1. The user has the capability
to manually select one of the two inputs or to configure an automatic switching mode operation. A detailed
description of this function is described in the uWire programming section of this data sheet.
PLL2 OSCin / OSCin* Port
The feedback from the external oscillator being locked with PLL1 is injected to the PLL2 OSCin/OSCin* pins.
This input may be driven with either a single- ended or differential signal. If operated in single ended mode, the
unused input should be tied to GND with a 0.1 F capacitor. Either AC or DC coupling is acceptable. Internal to
the chip, this signal is routed to the PLL1_N Counter and to the reference input for PLL2. The internal circuitry of
the OSCin port also supports the optional implementation of a crystal based oscillator circuit. A crystal, varactor
diode and a small number of other external components may be used to implement the oscillator. The internal
oscillator circuit is enabled by setting the EN_PLL2_XTAL bit.
CPout1 / CPout2
The CPout1 pin provides the charge pump current output to drive the loop filter for PLL1. This loop filter should
be configured so that the total loop bandwidth for PLL1 is less than 200 Hz. When combined with an external
oscillator that has low phase noise at offsets close to the carrier, PLL1 generates a reference for PLL2 that is
frequency locked to the PLL1 reference clock but has the phase noise performance of the oscillator. The CPout2
pin provides the charge pump current output to drive the loop filter for PLL2. This loop filter should be configured
so that the total loop bandwidth for PLL2 is in the range of 50 kHz to 200 kHz. See the section on uWire device
control for a description of the charge pump current gain control.
26
Copyright 2008–2011, Texas Instruments Incorporated
相關PDF資料
PDF描述
M83723/86G10206 CONN PLUG 2POS STRAIGHT W/SCKT
MS27472E18A53S CONN RCPT 53POS WALL MT W/SCKT
CS3106A-32-73P CONN PLUG 46POS STRAIGHT W/PINS
LMK04000BISQE/NOPB IC CLOCK COND 1.2GHZ W/PLL 48LLP
VE-B4W-MV CONVERTER MOD DC/DC 5.5V 150W
相關代理商/技術參數
參數描述
LMK04001BISQX 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Low-Noise Clock Jitter Cleaner with Cascaded PLLs
LMK04001BISQX/NOPB 功能描述:時鐘合成器/抖動清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
LMK04002BEVAL 功能描述:時鐘和定時器開發工具 LMK04002 EVAL BOARD RoHS:否 制造商:Texas Instruments 產品:Evaluation Modules 類型:Clock Conditioners 工具用于評估:LMK04100B 頻率:122.8 MHz 工作電源電壓:3.3 V
LMK04002BEVAL/NOPB 功能描述:BOARD EVAL FOR LMK04002B RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:PowerWise® 標準包裝:1 系列:- 主要目的:數字電位器 嵌入式:- 已用 IC / 零件:AD5258 主要屬性:- 次要屬性:- 已供物品:板 相關產品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP
LMK04002BISQ 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Low-Noise Clock Jitter Cleaner with Cascaded PLLs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*