- 您現在的位置：買賣IC網 > PDF目錄44546 > LM25066PSQX (NATIONAL SEMICONDUCTOR CORP) POWER SUPPLY SUPPORT CKT, QCC24 PDF資料下載
參數資料
| 型號： | LM25066PSQX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 電源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, QCC24 |
| 封裝： | LLP-24 |
| 文件頁數： | 19/48頁 |
| 文件大小： | 1456K |
| 代理商： | LM25066PSQX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
- The high current path from the board’s input to the load (via
Q
1) and the return path should be parallel and close to each
other to minimize parasitic loop inductance.
- The ground connections for the various components around
the LM25066 should be connected directly to each other and
to the LM25066’s GND pin and then connected to the system
ground at one point. Do not connect the various component
grounds to each other through the high current ground line.
For more details, see application note AN-2100.
- Provide adequate heat sinking for the series pass device
(Q
1) to help reduce stresses during turn-on and turn-off.
- Keep the gate trace from the LM25066 to the pass MOSFET
short and direct.
- The board’s edge connector can be designed such that the
LM25066 detects via the UVLO/EN pin that the board is being
removed and responds by turning off the load before the sup-
ply voltage is disconnected. For example, in Figure 17, the
voltage at the UVLO/EN pin goes to ground before V
SYS is
removed from the LM25066 because of the shorter edge con-
nector pin. When the board is inserted into the edge connec-
tor, the system voltage is applied to the LM25066’s VIN pin
before the UVLO voltage is taken high, thereby allowing the
LM25066 to turn on the output in a controlled fashion.
30115853
FIGURE 17. Recommended Board Connector Design
www.national.com
26
LM25066
相關PDF資料 |
PDF描述 |
|---|---|
| LM25066PSQ | POWER SUPPLY SUPPORT CKT, QCC24 |
| LM25574Q0MT | SWITCHING REGULATOR, PDSO16 |
| LM25574Q0MTX | SWITCHING REGULATOR, PDSO16 |
| LM25576Q0MH | SWITCHING REGULATOR, PDSO20 |
| LM2574HVADJMWC | 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, UUC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM25066PSQX/NOPB | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| LM25069 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Positive Low Voltage Power Limiting Hot Swap Controller |
| LM25069MM-2EVAL | 功能描述:BOARD EVALUATION LM25069 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| LM25069MM-2EVAL/NOPB | 功能描述:電源管理IC開發工具 LM25069MM-2 Eval Brd RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| LM25069PMM-1 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Positive Low Voltage Power Limiting Hot Swap Controller |
發布緊急采購，3分鐘左右您將得到回復。