- 您現在的位置：買賣IC網 > PDF目錄98000 > LM25066APSQE (NATIONAL SEMICONDUCTOR CORP) POWER SUPPLY SUPPORT CKT, QCC24 PDF資料下載
參數資料
| 型號： | LM25066APSQE |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 電源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, QCC24 |
| 封裝： | LLP-24 |
| 文件頁數： | 6/48頁 |
| 文件大小： | 1658K |
| 代理商： | LM25066APSQE |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
30146013
FIGURE 2. Power Up Sequence (Current Limit Only)
Gate Control
A charge pump provides the voltage at the GATE pin to en-
hance the N-Channel MOSFET’s gate. During normal oper-
ating conditions (t
by an internal 22 A current source. The voltage at the GATE
pin (with respect to ground) is limited by an internal 18.8 V
zener diode. See the graph “GATE Pin Voltage” provided
previously. Since the gate-to-source voltage applied to Q
1
could be as high as 18.8 V during various conditions, a zener
diode with the appropriate voltage rating must be added be-
tween the GATE and OUT pins if the maximum V
GS rating of
the selected MOSFET is less than 18.8 V. The external zener
diode must have a forward current rating of at least 190 mA.
When the system voltage is initially applied, the GATE pin is
held low by a 190 mA pull-down current. This helps prevent
an inadvertent turn-on of the MOSFET through its drain-gate
capacitance as the applied system voltage increases.
During the insertion time (t
1 in Figure 2), the GATE pin is held
low by a 2 mA pull-down current. This maintains Q
1 in the off-
state until the end of t
1, regardless of the voltage at VIN or
UVLO. Following the insertion time, during t
2 in Figure 2, the
gate voltage of Q
1 is controlled to keep the current or power
dissipation level from exceeding the programmed levels.
While in the current or power limiting mode, the TIMER pin
capacitor is charging. If the current and power limiting cease
before the TIMER pin reaches 1.7V, the TIMER pin capacitor
then discharges, and the circuit begins normal operation. If
the inrush limiting condition persists such that the TIMER pin
reached 1.7V during t
2, the GATE pin is then pulled low by the
190 mA pull-down current. The GATE pin is then held low until
either a power up sequence is initiated (RETRY pin to VDD)
or an automatic retry is attempted (RETRY pin to GROUND).
See the Fault Timer & Restart section. If the system input
voltage falls below the UVLO threshold or rises above the
OVLO threshold, the GATE pin is pulled low by the 2 mA pull-
down current to switch off Q
1.
Current Limit
The current limit threshold is reached when the voltage across
the sense resistor R
S (VIN to SENSE) exceeds the internal
voltage limit of 25 mV or 46 mV depending on whether the CL
pin is connected to GND or VDD, respectively. In the current
limiting condition, the GATE voltage is controlled to limit the
current in MOSFET Q
1. While the current limit circuit is active,
the fault timer is active as described in the Fault Timer &
Restart section. If the load current falls below the current limit
threshold before the end of the Fault Timeout Period, the
LM25066A resumes normal operation. If the current limit con-
dition persists for longer than the Fault Timeout Period set by
the timer capacitor, C
T, the IIN OC FAULT bit in the
www.national.com
14
LM25066A
相關PDF資料 |
PDF描述 |
|---|---|
| LM2575T-012G | 3.2 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, SFM5 |
| LM2577K-12/883 | 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, MBFM2 |
| LM2577KADJ/883 | 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, MBCY4 |
| LM2577K-15/883 | 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, MBFM2 |
| LM2633MTDX/NOPB | SWITCHING CONTROLLER, 275 kHz SWITCHING FREQ-MAX, PDSO48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM25066APSQE/NOPB | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| LM25066APSQX | 制造商:TI 制造商全稱:Texas Instruments 功能描述:System Power Management and Protection IC with PMBusa?￠ |
| LM25066APSQX/NOPB | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| LM25066EVK/NOPB | 功能描述:電源管理IC開發(fā)工具 LM25066 EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| LM25066IAPSQ/NOPB | 制造商:Texas Instruments 功能描述:IC PWR MGMT/PROT PMBUS 24WQFN 制造商:Texas Instruments 功能描述:System PWR Mgmt & Protection IC |
發(fā)布緊急采購，3分鐘左右您將得到回復。