- 您現在的位置：買賣IC網 > PDF目錄98000 > LM25066APSQE (NATIONAL SEMICONDUCTOR CORP) POWER SUPPLY SUPPORT CKT, QCC24 PDF資料下載
參數資料
| 型號： | LM25066APSQE |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 電源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, QCC24 |
| 封裝： | LLP-24 |
| 文件頁數： | 24/48頁 |
| 文件大?。?/td> | 1658K |
| 代理商： | LM25066APSQE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
TABLE 7. VIN_OV_WARN_LIMIT Register
Value
Meaning
Default
0h – 0FFEh
VIN Over-voltage
Warning detection
threshold
0FFFh (disabled)
0FFFh
VIN Over-voltage
Warning disabled
n/a
VIN_UV_WARN_LIMIT (58h)
The VIN_UV_WARN_LIMIT command is a standard PM-
Bus command that allows configuring or reading the thresh-
old for the VIN under-voltage warning detection. Reading and
writing to this register should use the coefficients shown in the
Telemetry and Warning Conversion Coefficients Table. Ac-
cesses to this command should use the PMBus read or
write word protocol. If the measured value of VIN falls below
the value in this register, VIN UV Warn flags are set in the
respective registers, and the SMBA signal is asserted.
TABLE 8. VIN_UV_WARN_LIMIT Register
Value
Meaning
Default
1h – 0FFFh
VIN Under-voltage
Warning detection
threshold
0000h (disabled)
0000h
VIN Under-voltage
Warning disabled
n/a
STATUS_BYTE (78h)
The STATUS_BYTE is a standard PMBus command that
returns the value of a number of flags indicating the state of
the LM25066A. Accesses to this command should use the
PMBus read byte protocol. To clear bits in this register, the
underlying fault should be removed and a CLEAR_FAULTS
command issued.
TABLE 9. STATUS_BYTE Definitions
Bit
NAME
Meaning
Default
7
BUSY
Not Supported, always 0
0
6
OFF
This bit is asserted if the MOSFET is not switched on
for any reason.
1
5
VOUT OV
Not Supported, always 0
0
4
IOUT OC
Not Supported, always 0
0
3
VIN UV FAULT
A VIN Under-voltage Fault has occurred
1
2
TEMPERATURE
A Temperature Fault or Warning has occurred
0
1
CML
A Communication Fault has occurred
0
None of the Above
A fault or warning not listed in bits [7:1] has occurred
1
STATUS_WORD (79h)
The STATUS_WORD command is a standard PMBus com-
mand that returns the value of a number of flags indicating the
state of the LM25066A. Accesses to this command should
use the PMBus read word protocol. To clear bits in this
register, the underlying fault should be removed and a
CLEAR_FAULTS command issued. The INPUT and VIN UV
FAULT flags will default to 1 on startup. However, they will be
cleared to 0 after the first time the input voltage exceeds the
resistor programmed UVLO threshold.
TABLE 10. STATUS_WORD Definitions
Bit
NAME
Meaning
Default
15
VOUT
An output voltage fault or warning has occurred
0
14
IOUT/POUT
Not Supported, always 0
0
13
INPUT
An input voltage or current fault has occurred
1
12
MFR
A Manufacturer Specific Fault or Warning has occurred
1
11
POWER GOOD
The Power Good signal has been negated
1
10
FANS
Not Supported, always 0
0
9
OTHER
Not Supported, always 0
0
8
UNKNOWN
Not Supported, always 0
0
7
BUSY
Not Supported, always 0
0
6
OFF
This bit is asserted if the MOSFET is not switched on for
any reason.
1
5
VOUT OV
Not Supported, always 0
0
4
IOUT OC
Not Supported, always 0
0
3
VIN UV FAULT
A VIN Under-voltage Fault has occurred
1
2
TEMPERATURE
A Temperature Fault or Warning has occurred
0
1
CML
A Communication Fault has occurred
0
None of the Above
A fault or warning not listed in bits [7:1] has occurred
1
www.national.com
30
LM25066A
相關PDF資料 |
PDF描述 |
|---|---|
| LM2575T-012G | 3.2 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, SFM5 |
| LM2577K-12/883 | 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, MBFM2 |
| LM2577KADJ/883 | 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, MBCY4 |
| LM2577K-15/883 | 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, MBFM2 |
| LM2633MTDX/NOPB | SWITCHING CONTROLLER, 275 kHz SWITCHING FREQ-MAX, PDSO48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM25066APSQE/NOPB | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| LM25066APSQX | 制造商:TI 制造商全稱:Texas Instruments 功能描述:System Power Management and Protection IC with PMBusa?￠ |
| LM25066APSQX/NOPB | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| LM25066EVK/NOPB | 功能描述:電源管理IC開發工具 LM25066 EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| LM25066IAPSQ/NOPB | 制造商:Texas Instruments 功能描述:IC PWR MGMT/PROT PMBUS 24WQFN 制造商:Texas Instruments 功能描述:System PWR Mgmt & Protection IC |
發布緊急采購，3分鐘左右您將得到回復。
