- 您現在的位置：買賣IC網 > PDF目錄98000 > LM25066APSQE (NATIONAL SEMICONDUCTOR CORP) POWER SUPPLY SUPPORT CKT, QCC24 PDF資料下載
參數資料
| 型號： | LM25066APSQE |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 電源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, QCC24 |
| 封裝： | LLP-24 |
| 文件頁數： | 10/48頁 |
| 文件大?。?/td> | 1658K |
| 代理商： | LM25066APSQE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
Application Section
30146001
FIGURE 6. Typical Application Circuit
DESIGN-IN PROCEDURE
(Refer to Figure 6 for Typical Application Circuit) Shown here
is the step-by-step procedure for hardware design of the
LM25066A. This procedure refers to section numbers that
provide detailed information on the following design steps.
The recommended design-in procedure is as follows:
MOSFET Selection:
Determine MOSFET value based on
breakdown voltage, current and power ratings.
Current Limit, R
S: Determine the current limit threshold
(I
LIM). This threshold must be higher than the normal maxi-
mum load current, allowing for tolerances in the current sense
resistor value and the LM25066A Current Limit threshold volt-
age. Use equation 1 to determine the value for R
S.
Power Limit Threshold:
Determine the maximum allowable
power dissipation for the series pass MOSFET (Q
1) using the
device’s SOA information. Use equation 2 to determine the
value for R
PWR.
Turn-On Time and TIMER Capacitor, C
T: Determine the
value for the timing capacitor at the TIMER pin (C
T) using
equation 8. The fault timeout period (t
FAULT) MUST be longer
than the circuit’s turn-on time. The turn-on time can be esti-
mated using the equations in the TURN-ON TIME section of
this data sheet, but should be verified experimentally. Review
the resulting insertion time, and the restart timing if retry is
enabled.
UVLO, OVLO:
Choose option A, B, C, or D from the UVLO,
OVLO section of the Application Information to set the UVLO
and OVLO thresholds and hysteresis. Use the procedure for
the appropriate option to determine the resistor values at the
UVLO/EN and OVLO pins.
Power Good:
Choose the appropriate output voltage and
calculate the required resistor divider from the output voltage
to the FB pin. Choose either VDD or OUT to connect properly
sized pull-up resistor for the Power Good output (PGD).
Refer to Programming Guide section:
After all hardware
design is complete, refer to the programming guide for a step
by step procedure regarding software.
MOSFET SELECTION
It is recommended that the external MOSFET (Q
1) selection
be based on the following criteria:
- The BV
DSS rating should be greater than the maximum sys-
tem voltage (V
SYS), plus ringing and transients which can
occur at V
SYS when the circuit card, or adjacent cards, are
inserted or removed.
- The maximum continuous current rating should be based on
the current limit threshold (e.g. 25 mV/R
S), not the maximum
load current, since the circuit can operate near the current
limit threshold continuously.
- The Pulsed Drain Current spec (I
DM) must be greater than
the current threshold for the circuit breaker function (45 mV/
R
S when CL = CB = GND).
- The SOA (Safe Operating Area) chart of the device and the
thermal properties should be used to determine the maximum
power dissipation threshold set by the R
PWR resistor. The
programmed maximum power dissipation should have a rea-
sonable margin from the maximum power defined by the
MOSFET’s SOA curve (if the device is set to infinitely retry,
the MOSFET will be repeatedly stressed during fault restart
www.national.com
18
LM25066A
相關PDF資料 |
PDF描述 |
|---|---|
| LM2575T-012G | 3.2 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, SFM5 |
| LM2577K-12/883 | 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, MBFM2 |
| LM2577KADJ/883 | 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, MBCY4 |
| LM2577K-15/883 | 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, MBFM2 |
| LM2633MTDX/NOPB | SWITCHING CONTROLLER, 275 kHz SWITCHING FREQ-MAX, PDSO48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM25066APSQE/NOPB | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| LM25066APSQX | 制造商:TI 制造商全稱:Texas Instruments 功能描述:System Power Management and Protection IC with PMBusa?￠ |
| LM25066APSQX/NOPB | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| LM25066EVK/NOPB | 功能描述:電源管理IC開發(fā)工具 LM25066 EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| LM25066IAPSQ/NOPB | 制造商:Texas Instruments 功能描述:IC PWR MGMT/PROT PMBUS 24WQFN 制造商:Texas Instruments 功能描述:System PWR Mgmt & Protection IC |
發(fā)布緊急采購，3分鐘左右您將得到回復。