- 您現在的位置：買賣IC網 > PDF目錄383133 > ISL5217EVAL1 (Intersil Corporation) Quad Programmable Up Converter PDF資料下載
參數資料
| 型號： | ISL5217EVAL1 |
| 廠商： | Intersil Corporation |
| 英文描述： | Quad Programmable Up Converter |
| 中文描述： | 四可編程轉換器 |
| 文件頁數： | 37/43頁 |
| 文件大小： | 766K |
| 代理商： | ISL5217EVAL1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁
37
TABLE 42. I AND Q CHANNEL COEFFICIENTS (15:0)
TYPE: SINGLE CHANNEL INDIRECT, ADDRESS RANGE: 0x300-0x3ff (PAGE 3)
FUNCTION
Filter coefficient
256 location RAM. Use this page when the I and Q coefficients are the same.
BIT
15:0
DESCRIPTION
NOTES:
Coefficients
RAM Read/Write Procedure (2’s complement format only)
Write
access to the Coefficient RAMs when I equal Q:
1. Enable the
μ
P hold mode by setting bit 12 of the Main Control register 0x0c.
2. Load the RAM data to location 0x14 with the coefficient.
3. Load the RAM write address to location 0x15. A write strobe transfers the contents of the register at location 0x14 into the RAM location
specified by the contents of the register at location 0x15. (Indirect address[15] =0, Indirect address[9:8]=”11”).
4. Wait 4 clock cycles before performing the next write to the RAM data register.
5. Repeat steps 2-4.
6. Return RAM control back to the channel by disabling the
μ
P hold mode.
Read
access to the Q Coefficient RAM:
1. Enable the
μ
P hold mode by setting bit 12 of the Main Control register 0x0c.
2. Load the RAM read address to location 0x15. A read strobe transfers the contents of the RAM location specified by the contents of the register
at location 0x15 onto the read bus. (Indirect address[15] =1, Indirect address[9:8]=”11”).
3. Wait 4 clock cycles before performing the next write to the RAM address register.
4. After all data has been loaded, return RAM control back to the channel by disabling the
μ
P hold mode.
TABLE 43. TXENX CONTROL
TYPE: SINGLE CHANNEL INDIRECT, ADDRESS RANGE: 0x400-0x407 (PAGE 4)
INDIRECT
ADDRESS
0x400
0x401
0x402
0x403
0x404 -
0x406
0x407
NOTES:
FSRMode affects what is output on the channel FSRX pin, but only if TXENX control, control word 0x0c, bit 11 is set to one. The FSRMode<1:0> is
defined as:
00 No change to FSRX output.
01 No change to FSRX output.
10 FSR = internal channel UPDX.
11 FSR = internal channel TXENX. TXENX SIB control (0x0c, bit 3) must be set when FSRMode 11 is utilized, otherwise a TXENX glitch will be
observed on the rising edge of TXENX.
To start the TXENX cycle function following a reset, the user must provide a normal channel update via one of the 2 possible update mechanisms
(software or hardware). An update also resets all of the TXENX counters and starts the device up in cycle 0 with TXENX high.
Write
access to the TXENX cycle controls:
1. Enable the
μ
P hold mode by setting bit 12 of the Main Control register 0x0c.
2. Load the data to location 0x14.
3. Load the indirect write address to location 0x15. A write strobe transfers the contents of the register at location 0x14 into the location specified
by the contents of the register at location 0x15. (Indirect address[15] =0).
4. Assert the write strobe again to update the configuration register.
5. Wait 4 clock cycles before performing the next write to the data register.
6. Repeat steps 2-5.
7. Return control back to the channel by disabling the
μ
P hold mode.
Read
access to the TXENX cycle controls:
Care should be utilized to only read registers back immediately after writing since loading indirect addr 0x15 with 040X causes 0x040X to get
loaded with indirect register 0x14’s contents.
1. Enable the
μ
P hold mode by setting bit 12 of the Main Control register 0x0c.
2. Load the read address to location 0x15. A read strobe transfers the contents of the RAM location specified by the contents of the register at
location 0x15 onto the read bus. (Indirect address[15] =1).
3. Wait 4 clock cycles before performing the next write to the address register.
4. Return control back to the channel by disabling the
μ
P hold mode.
FUNCTION
DESCRIPTION
TXENX Cycle 0 Low
TXENX Cycle 0 High
TXENX Cycle 1 Low
TXENX Cycle 1 High
Reserved
TXENX cycle 0 low time count <15:0>.
TXENX cycle 0 high time count <15:0>.
TXENX cycle 1 low time count <15:0>.
TXENX cycle 1 high time count <15:0>.
Not Used.
TXENX Cycle Lengths
FSRMode<1:0>, cycle 1 length<4:0>, cycle 0 length<4:0>
ISL5217
相關PDF資料 |
PDF描述 |
|---|---|
| ISL5217KI | Quad Programmable Up Converter |
| ISL5217 | Quad Programmable Up Converter |
| ISL5217KIZ | Quad Programmable Up Converter |
| ISL5314INZ | Direct Digital Synthesizer |
| ISL5314IN | Direct Digital Synthesizer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL5217KI | 功能描述:上下轉換器 196BGA,-40+85C PROGRAMMABLE QUAD UP CONVERTER RoHS:否 制造商:Texas Instruments 產品:Down Converters 射頻:52 MHz to 78 MHz 中頻:300 MHz LO頻率: 功率增益: P1dB: 工作電源電壓:1.8 V, 3.3 V 工作電源電流:120 mA 最大功率耗散:1 W 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-128 |
| ISL5217KIZ | 制造商:Intersil Corporation 功能描述:UP/DOWN CONV MIXER 2.5V 196BGA - Trays 制造商:Intersil 功能描述:W/ANNEAL 196BGA -40+ 85C PROG CONVER |
| ISL5239 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Pre-Distortion Linearizer |
| ISL5239EVAL1 | 功能描述:EVALUATION BOARD FOR ISL5239 RoHS:是 類別:RF/IF 和 RFID >> RF 評估和開發套件，板 系列:- 標準包裝:1 系列:- 類型:GPS 接收器 頻率:1575MHz 適用于相關產品:- 已供物品:模塊 其它名稱:SER3796 |
| ISL5239KI | 功能描述:音頻 DSP PA LINEARIZER IND TEMP 1 0MM PITCH RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。