- 您現在的位置：買賣IC網 > PDF目錄360706 > IBM3209K4060 Telecom Switching Circuit PDF資料下載
參數資料
| 型號： | IBM3209K4060 |
| 英文描述： | Telecom Switching Circuit |
| 中文描述： | 電信開關電路 |
| 文件頁數： | 95/131頁 |
| 文件大小： | 1679K |
| 代理商： | IBM3209K4060 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁當前第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁
PRS28.4G
IBM Packet Routing Switch
prs28.03.fm
August 31, 2000
I/O Definitions and Timing
Page 95 of 131
Flow Control Signals
MEM_GRANT(0:3)
Output
MEM_GRANT(
n
) provides the grant status of the shared memory for priority
n
.
The MEM_GRANT pins are updated every four clock cycles (of 9 to 10 ns).
See
Functional Description
on page 25.
The device pin encoding and corresponding grant definition is as follows:
0000:
No Grant
1000:
Priority 0, or control packets
1100:
Priority 0 or 1, or control packets
1110:
Priority 0 .. 2, or control packets
1111:
Priority 0 .. 3, or control packets
others: Reserved.
The MEM_GRANT device pins are always active and always reflect the latest mem-
ory full information.
When two devices are in external speed expansion, only the MEM_GRANT bus from
the master device is used.
SND_GRANT(0:15)
Input
Grants the output ports the opportunity to transmit packets. When bit
n
is active, a
packet can be transmitted on port
n
. When inactive, Data Packets are not allowed to
be transmitted, and only Idle Packets will come out. Note that, when a Data packet is
to be transmitted, the packet of highest available priority will be transmitted.
When two devices are in external speed expansion, the SND_GRANT bus of the
slave device is not used and thus not connected (internal pull-up).
RCV_GRANT(0:15)
Input
Provides a grant to receive packets for each output. Incoming packets will only be
received for output
n
if the RCV_GRANT(
n
) is active high. Packets destined for out-
puts for which the RCV_GRANT is deasserted will not be enqueued in those outputs.
The RCV_GRANT pins are to be used only for Data Packets with Active bit = ‘1’b, and
Backup bit = ‘0’b.
When two devices are in external speed expansion, the RCV_GRANT bus of the
slave device is not used and thus not connected (internal pull-up).
Q_FULL(0:15)
Output
Provides the full status of all 16 output queues. Bit
n
carries the status of output queue
n
, for all priorities, in the time multiplexed manner. For each priority, the signal is valid
for four clock cycles. When Q_SYNC is active high, Q_FULL carries the status of the
16 queues for priority 0. It is followed four cycles later by priority 1, in another four
cycles by priority 2, in another four cycles by priority 3. Note that only the number of
priorities programmed in the Configuration Register 0 is reported. Thus, if only three
priorities are enabled, the multiplexing cycle will be: priority 0 (Q_SYNC active), prior-
ity 1, priority 2, priority 0 (Q_SYNC active) and so forth.
When two devices are in external speed expansion, only the Q_FULL bus from the
master device is used.
Q_EMPTY(0:15)
Output
Provides the empty status of all 16 output queues. Bit n carries the status of output
queue n, for all priorities, in the time multiplexed manner. For each priority, the signal
is valid for four clock cycles. When Q_SYNC is active high, Q_EMPTY, carries the
status of the 16 queues for priority 0. It is followed four cycles later by priority 1, in
another four cycles by priority 2, and in another four cycles by priority 3. Note that only
the number of priorities programmed in the Configuration Register 0 is reported. Thus,
if only three priorities are enabled, the multiplexing cycle will be: priority 0 (Q_SYNC
active), priority 1, priority 2, priority 0 (Q_SYNC active), and so forth.
When two devices are in external speed expansion, only the Q_EMPTY bus from the
master device is used.
Q_SYNC
Output
Used as a framing bit for the Q_FULL(0:15) and Q_EMPTY(0:15) busses and is active
when the status of priority 0 is valid for all 16 bits of the bus.
When two devices are in external speed expansion, only the Q_SYNC bit from the
master device is used.
Table 21: Signal Definitions
(Page 2 of 6)
Signal Name
Type
Description
相關PDF資料 |
PDF描述 |
|---|---|
| IBM3288H2848 | Telecommunication IC |
| IBM32NPR100EXXCAB133 | Microprocessor |
| IBM32NPR101EPXCAC133 | Microprocessor |
| IBM37RGB524CF17A | Video DAC with Color Palette (RAMDAC) |
| IBM37RGB524CF22A | Video DAC with Color Palette (RAMDAC) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IBM3288H2848 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| IBM32NPR100EXXCAB133 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor |
| IBM32NPR101EPXCAC133 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor |
| IBM35CPC945C03C-2 | 制造商:IBM 功能描述: |
| IBM37RGB524CF17A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Video DAC with Color Palette (RAMDAC) |
發布緊急采購，3分鐘左右您將得到回復。