- 您現在的位置：買賣IC網 > PDF目錄360706 > IBM3209K4060 Telecom Switching Circuit PDF資料下載
參數資料
| 型號： | IBM3209K4060 |
| 英文描述： | Telecom Switching Circuit |
| 中文描述： | 電信開關電路 |
| 文件頁數： | 50/131頁 |
| 文件大?。?/td> | 1679K |
| 代理商： | IBM3209K4060 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁
PRS28.4G
IBM Packet Routing Switch
Programming Interface and Internal Registers
Page 50 of 131
prs28.03.fm
August 31, 2000
4.1.5 Operational Protocol
OCM Instruction operations are invoked when the EMB_MODE input is `0' and the EMB_SELECT input is `0'.
Data transferred over EMB_DATA_IN is shifted into the OCM instruction register. Serial data shifted in must
begin with the least significant bit of the instruction and end with the most significant bit of the instruction to be
executed. This scan operation is synchronized with the EMB CLOCK lines. Instructions always execute one
cycle after the EMB_SELECT changes from an active to an inactive state. “OCM Instruction Mode
Sequence,” table describes the sequence of events required to load and execute an OCM instruction.
When configured in a daisy chain (ring) structure, targeted OCMs (that is those with no instruction to execute)
must be loaded with NOOP instructions.
4.2 OCM Scan Mode
Note:
This mode is for system bring-up only.
4.2.1 Operational Protocol
Before a scan operation can occur, the system clock must be stopped and a scan string must be selected
using the OCM EVENT command. The clocks can be stopped and a scan string selected by issuing either
one or two EVENT instruction. Or, two separate EVENT instructions can be issued.
Scan operations are invoked when the EMB_MODE input is `1'b and the EMB_SELECT input is `0'b. Data
transferred over EMB_DATA_IN is serially shifted into the selected scan string. The logic values located
within the scan string are serially shifted out of the scan string over the EMB_DATA_OUT primary output.
One bit of data is shifted with each EMB A/B clock sequence.
The table below is a summary of the sequence of operations required to perform a scan write operation to an
OCM in a ring structure.
Table 15: OCM Instruction Mode Sequence
Controller Action
OCM Action/Response
Set EMB_MODE = 0; EMB_SELECT = 0 (Active)
Instruction/status operation specified
Serially shift instructions to all OCMs - NOOPs must be
loaded into all non-targeted OCMs
As instructions are serially shifted in through the EMB_DATA_IN pin.
The response word (that is, the results of the previous instruction) is
shifted out through the EMB_DATA_OUT pin.
Set EMB_SELECT = 1 (Inactive)
Instruction shifted mode is terminated and the currently load instruction
is executed. The contents of the OCM response register are instruction
dependent. Refer to “OCM Instruction Set definition” table for a
description of the individual instructions and a definition of the
response register contents following instruction execution.
Table 16: OCM Scan Mode Sequence
Controller Action
OCM Action/Response
Send EVENT instructions to all OCMs to stop system clocks (if
needed) and select one of two scan strings.
The OCMs will execute the EVENT instruction. The system clock
control command will be executed first, and then the selected
scan string will be placed between EMB_DATA_IN and
EMB_DATA_OUT.
Set EMB_MODE = 1; EMB_SELECT = 0 (Active).
相關PDF資料 |
PDF描述 |
|---|---|
| IBM3288H2848 | Telecommunication IC |
| IBM32NPR100EXXCAB133 | Microprocessor |
| IBM32NPR101EPXCAC133 | Microprocessor |
| IBM37RGB524CF17A | Video DAC with Color Palette (RAMDAC) |
| IBM37RGB524CF22A | Video DAC with Color Palette (RAMDAC) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IBM3288H2848 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| IBM32NPR100EXXCAB133 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor |
| IBM32NPR101EPXCAC133 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor |
| IBM35CPC945C03C-2 | 制造商:IBM 功能描述: |
| IBM37RGB524CF17A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Video DAC with Color Palette (RAMDAC) |
發布緊急采購，3分鐘左右您將得到回復。