- 您現在的位置：買賣IC網 > PDF目錄370782 > HYB18T512160AF-3 (INFINEON TECHNOLOGIES AG) 512-Mbit DDR2 SDRAM PDF資料下載
參數資料
| 型號： | HYB18T512160AF-3 |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 英文描述： | 512-Mbit DDR2 SDRAM |
| 中文描述： | 512兆位DDR2 SDRAM的 |
| 文件頁數： | 67/117頁 |
| 文件大?。?/td> | 2102K |
| 代理商： | HYB18T512160AF-3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁當前第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁
Data Sheet
67
Rev. 1.3, 2005-01
09112003-SDM9-IQ3P
HYB18T512[40/80/16]0AF–[3/3S/3.7/5]
512-Mbit DDR2 SDRAM
Functional Description
3.23.4
Concurrent Auto-Precharge
DDR2 devices support the “Concurrent Auto-
Precharge” feature. A Read with Auto-Precharge
enabled, or a Write with Auto-Precharge enabled, may
be followed by any command to the other bank, as long
as that command does not interrupt the read or write
data transfer, and all other related limitations (e.g.
contention between Read data and Write data must be
avoided externally and on the internal data bus).
The minimum delay from a Read or Write command
with Auto-Precharge enabled, to a command to a
different bank, is summarized in the Command Delay
Table. As defined, the WL = RL - 1 for DDR2 devices
which allows the command gap and corresponding
data gaps to be minimized.
3.24
Refresh
DDR2 SDRAM requires a refresh of all rows in any rolling 64 ms interval. The necessary refresh can be generated
in one of two ways: by explicit Auto-Refresh commands or by an internally timed Self-Refresh mode.
3.24.1
Auto-Refresh Command
Auto-Refresh is used during normal operation of the
DDR2 SDRAM’s. This command is non persistent, so it
must be issued each time a refresh is required. The
refresh addressing is generated by the internal refresh
controller. This makes the address bits ”don’t care”
during an Auto-Refresh command. The DDR2 SDRAM
requires Auto-Refresh cycles at an average periodic
interval of
t
REFI.MAX
.
When CS, RAS and CAS are held LOW and WE HIGH
at the rising edge of the clock, the chip enters the Auto-
Refresh mode. All banks of the SDRAM must be
precharged and idle for a minimum of the precharge
time (
t
RP
) before the Auto-Refresh Command can be
applied. An internal address counter supplies the
addresses during the refresh cycle. No control of the
external address bus is required once this cycle has
started.
When the refresh cycle has completed, all banks of the
SDRAM will be in the precharged (idle) state. A delay
between the Auto-Refresh Command and the next
Activate Command or subsequent Auto-Refresh
Command must be greater than or equal to the Auto-
Refresh cycle time (
t
RFC
).
To allow for improved efficiency in scheduling and
switching between tasks, some flexibility in the
absolute refresh interval is provided. A maximum of
eight Auto-Refresh commands can be posted to any
given DDR2 SDRAM, meaning that the maximum
absolute interval between any Auto-Refresh command
and the next Auto-Refresh command is 9
×
t
REFI
.
Table 19
From Command To Command (different bank,
non-interrupting command)
WRITE w/AP
Read or Read w/AP
Write or Write w/AP
Precharge or Activate
Read w/AP
Read or Read w/AP
Write or Write w/AP
Precharge or Activate
Command Delay Table
Minimum Delay with Concurrent Auto-
Precharge Support
(CL -1) + (BL/2) +
t
WTR
BL/2
1
BL/2
BL/2 + 2
1
Unit
Note
t
CK
t
CK
t
CK
t
CK
t
CK
t
CK
1)
1) This rule only applies to a selective Precharge command to another bank, a Precharge-All command is illegal
1)
相關PDF資料 |
PDF描述 |
|---|---|
| HYB18T512160AF-3.7 | 512-Mbit DDR2 SDRAM |
| HYB18T512160AF-3S | 512-Mbit DDR2 SDRAM |
| HYB18T512400AF-3 | 512-Mbit DDR2 SDRAM |
| HYB18T512400AF-3S | 512-Mbit DDR2 SDRAM |
| HYB18T512800AF-3 | 512-Mbit DDR2 SDRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HYB18T512161BF-25 | 制造商:Qimonda 功能描述:SDRAM, DDR, 32M x 16, 84 Pin, Plastic, BGA |
| HYB18T512400AF-5 | 制造商:Intersil Corporation 功能描述:SDRAM, DDR, 128M x 4, 60 Pin, Plastic, BGA |
| HYB18T512400BF-3S | 制造商:Qimonda 功能描述: |
| HYB18T512800AF-3S | 制造商:Qimonda 功能描述: 制造商:Infineon Technologies AG 功能描述:32M X 16 DDR DRAM, 0.45 ns, PBGA84 |
| HYB18T512800BF-2.5 | 功能描述:IC DDR2 SDRAM 512MBIT 60TFBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:60 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:16K (2K x 8) 速度:2MHz 接口:SPI 3 線串行 電源電壓:2.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 產品目錄頁面:1449 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。