- 您現在的位置：買賣IC網 > PDF目錄1922 > FUSB2805MLX (Fairchild Semiconductor)TXRX USB2.0 HS OTG ULPI 32MLP PDF資料下載
參數資料
| 型號： | FUSB2805MLX |
| 廠商： | Fairchild Semiconductor |
| 文件頁數： | 22/49頁 |
| 文件大?。?/td> | 0K |
| 描述： | TXRX USB2.0 HS OTG ULPI 32MLP |
| 標準包裝： | 1 |
| 系列： | * |
| 其它名稱： | FUSB2805MLXFSDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
2008 Fairchild Semiconductor Corporation
www.fairchildsemi.com
FUSB2805 Rev. 1.0.3
29
F
USB2
8
0
5
—
USB2
.0
High
-S
pee
d
OTG
Tra
nsc
e
iv
e
rw
ith
UL
P
I
Inter
fac
e
Remote Wake Up
The FUSB2805 supports peripherals that can initiate
remote wake-up. When placed into USB suspend, the
peripheral remembers the speed at which it was
originally
operating.
Depending
on
that
original
operating speed, the link follows one of the protocols
described below.
The sequence of events is:
1.
Both the host and peripheral are assumed to be in
low-power mode.
2.
The
peripheral
begins
remote
wake-up
by
re-enabling the clock and setting its SUSPENDM
bit=1b.
3.
The peripheral begins driving a K-state on the bus
to signal resume. The peripheral link must assume
that LINESTATE is K (01b) while transmitting (since
it does not receive any RXCMDs).
4.
The host recognizes the resume, re-enables its
clock, and sets its SUSPENDM bit.
5.
The host takes over resume driving within 1ms of
detecting the remote wake-up.
6.
The peripheral stops driving resume.
7.
The peripheral recognizes the host continuing to
drive the resume.
8.
The host stops driving resume and the FUSB2805
automatically adds the EOP to the end of resume.
The peripheral recognizes the EOP as the end
of resume.
9.
Both the host and peripheral revert to normal
operation by writing OPMODE[1:0]=00b. If the host
or the peripheral was previously in HS mode, it
must revert to HS mode before the SE0 of the EOP
is completed. This can be achieved by writing
XCVRSELECT[1:0]=00b
and
TERMSELECT=0b
after LINESTATE indicates SE0.
Figure 17 shows the remote wake-up timing.
ULPI Peripheral
STP
NXT
T1
LS EOP Interval
DIR
NXT
ULPI Host
D+
D-
USB Signals
Remote Wake Up Timing
TermSelect=1b
XcvrSelect
TermSelect
OpMode
10 (chirp)
00
(Normal)
D [7:0]
TXCMD
NOPID
TXCMD
RegWr
RXCMD
TXCMD
RegWr
Linestate
00h
RXCMD
D [7:0]
TXCMD
RegWr
Linestate
00h
STP
TXCMD
NOPID
TXCMD
RegWr
01 (FS) or 10( LS)
XcvrSelect
TermSelect
OpMode
10 (chirp)
00
(Normal)
00 (HS only)
1
2
5
4
3
9
8
7
6
Termselect = 0b for HS only
00 (HS), 01 (FS) or 10( LS)
00 (HS only)
Figure 17.
Remote Wake-Up from Low-Power Mode
Note:
20. Timing is not to scale and not all the RXCMD LINESTATE updates or bus turn-around cycles are necessarily
shown. The bus turn-around cycles are included for one cycle after every assertion and de-assertion of DIR.
相關PDF資料 |
PDF描述 |
|---|---|
| FXLA2203UMX | TRANSLATOR LEVEL DUAL 24UMLP |
| GAL16V8D-15LJN | SPLD 62.5MHZ EECMOS 20 PLCC |
| GAL18V10B-20LP | IC GAL 10OUT MACROCELL 7.5NS 20 |
| GAL22V10D-25LJ | IC SPLD 3.3V 28-PLCC |
| GH65C11-C-PD | OPTO ENCODER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FUSCA REF BOARD | 制造商:TDK 功能描述:REFERENCE BOARD FUSCA 2.4GHZ |
| FUSCAREFBOARD | 制造商:Antenova 功能描述:Reference Board Fusca 2.4GHz |
| FUSE | 功能描述:保險絲 Fuse, Fiber 20A 600V Lot Qty 5 RoHS:否 制造商:Littelfuse 產品:Surface Mount Fuses 電流額定值:0.5 A 電壓額定值:600 V 保險絲類型:Fast Acting 保險絲大小/組:Nano 尺寸:12.1 mm L x 4.5 mm W 安裝風格: 端接類型:SMD/SMT 系列:485 |
| FUSE 25A ATC | 制造商:American Technical Ceramics Corp 功能描述: 制造商:ATC 功能描述: |
| FUSE KIT D | 制造商:COOPER BUSSMANN 功能描述:BUSSMANN FUSE KIT |
發布緊急采購，3分鐘左右您將得到回復。