參數資料
型號: FDC37C665IR
廠商: SMSC Corporation
英文描述: 3/5 Volt Advanced High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controller with Infranred Support
中文描述: 3 / 5伏先進的高性能多模并口超級I / O軟盤與Infranred支持磁盤控制器
文件頁數: 44/162頁
文件大?。?/td> 562K
代理商: FDC37C665IR
44
COMMAND SET/DESCRIPTIONS
Commands can be written whenever the FDC is
in the command phase. Each command has a
unique set of needed parameters and status
results. The FDC checks to see that the first
byte is a valid command and, if valid, proceeds
with the command. If it is invalid, an interrupt
is issued. The user sends a Sense Interrupt
Status command which returns an invalid
command error. Refer to Table 19 for
explanations of the various symbols used.
Table 20 lists the required parameters and the
results associated with each command that the
FDC is capable of performing.
Table 20 - Description of Command Symbols
NAME
Cylinder Address
The currently selected address; 0 to 255.
Data Pattern
The pattern to be written in each sector data field during
formatting.
Drive Select 0-3
Designates which drives are perpendicular drives on the
Perpendicular Mode Command. A "1" indicates a perpendicular
drive.
Direction Control
If this bit is 0, then the head will step out from the spindle during a
relative seek. If set to a 1, the head will step in toward the spindle.
Disk Drive Select
DS1 DS0 DRIVE
0 0 drive 0
0 1 drive 1
1 0 drive 2
1 1 drive 3
Special Sector
Size
of bytes transferred in disk read/write commands. The sector size
(N = 0) is set to 128. If the actual sector (on the diskette) is larger
than DTL, the remainder of the actual sector is read but is not
passed to the host during read commands; during write
commands, the remainder of the actual sector is written with all
zero bytes. The CRC check code is calculated with the actual
sector. When N is not zero, DTL has no meaning and should be
set to FF HEX.
Enable Count
When this bit is "1" the "DTL" parameter of the Verify command
becomes SC (number of sectors per track).
Enable FIFO
This active low bit when a 0, enables the FIFO. A "1" disables the
FIFO (default).
Enable Implied
Seek
read or write command that requires the C parameter in the
command phase. A "0" disables the implied seek.
End of Track
The final sector number of the current track.
Alters Gap 2 length when using Perpendicular Mode.
Gap Length
The Gap 3 size. (Gap 3 is the space between sectors excluding
the VCO synchronization field).
SYMBOL
C
D
DESCRIPTION
D0, D1, D2,
D3
DIR
DS0, DS1
DTL
By setting N to zero (00), DTL may be used to control the number
EC
EFIFO
EIS
When set, a seek operation will be performed before executing any
EOT
GAP
GPL
相關PDF資料
PDF描述
FDC37C665GT High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers
FDC37C666GT High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers
FDC37C67X ENHANCED SUPER I/O CONTROLLER WITH FAST IR
FDC37C957FR ULTRA I/O CONTROLLER FOR PORTABLE APPLICATIONS
FDC37M600 ENHANCED SUPER I/O CONTROLLER WITH INFRARED SUPPORT
相關代理商/技術參數
參數描述
FDC37C665IRQFP 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:SMSC 功能描述:
FDC37C666GT 制造商:SMSC 制造商全稱:SMSC 功能描述:High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers
FDC37C669 制造商:SMSC 制造商全稱:SMSC 功能描述:PC 98/99 Compliant Super I/O Floppy Disk Controller with Infrared Support
FDC37C669_07 制造商:SMSC 制造商全稱:SMSC 功能描述:PC 98/99 Compliant Super I/O Floppy Disk Controller with Infrared Support
FDC37C669FRQFP 制造商:Rochester Electronics LLC 功能描述:- Bulk