參數資料
型號： FDC37C665GT
廠商： STANDARD MICROSYSTEMS CORP
元件分類： 存儲控制器/管理單元
英文描述： High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers
中文描述： 1 Mbps, IDE COMPATIBLE, FLOPPY DISK DRIVE CONTROLLER, PQFP100
封裝： QFP-100
文件頁數： 71/162頁
文件大小： 562K
代理商： FDC37C665GT
71
When both GAP and WGATE bits of the
PERPENDICULAR MODE COMMAND are both
programmed to "0" (Conventional mode), then
D0, D1, D2, D3, and D4 can be programmed
independently to "1" for that drive to be set
automatically to Perpendicular mode. In this
mode the following set of conditions also apply:
1. The GAP2 written to a perpendicular drive
during a write operation will depend upon the
programmed data rate.
2. The write pre-compensation given to a
perpendicular mode drive wil be 0ns.
3. For
D0-D3
programmed
conventional mode drives any data written
will be at the currently programmed write
pre-compensation.
to
"0"
for
Note: Bits D0-D3 can only be overwritten when
OW is programmed as a "1".
If either GAP or WGATE is a "1" then
D0-D3 are ignored.
Software and hardware resets have the
following effect on the PERPENDICULAR
MODE COMMAND:
1. "Software" resets (via the DOR or DSR
registers) will only clear GAP and WGATE
bits to "0". D0-D3 are unaffected and retain
their previous value.
2. "Hardware" resets will clear all bits ( GAP,
WGATE and D0-D3) to "0", i.e all
conventional mode.
Table 31 - Effects of WGATE and GAP Bits
WGATE
GAP
MODE
LENGTH OF
GAP2
FORMAT
FIELD
22 Bytes
22 Bytes
PORTION OF
GAP 2
WRITTEN BY
WRITE DATA
OPERATION
0
0
1
1
0
1
0
1
Conventional
Perpendicular
(500 Kbps)
Reserved
(Conventional)
Perpendicular
(1 Mbps)
22 Bytes
41 Bytes
0 Bytes
19 Bytes
0 Bytes
38 Bytes
LOCK
In order to protect systems with long DMA
latencies against older application software that
can disable the FIFO the LOCK Command has
been added. This command should only be
used by the FDC routines, and application
software should refrain from using it. If an
application calls for the FIFO to be disabled
then the CONFIGURE command should be
used.
The LOCK command defines whether the
EFIFO, FIFOTHR, and PRETRK parameters of
the CONFIGURE command can be RESET by
the DOR and DSR registers. When the LOCK
bit is set to logic "1" all subsequent "software
RESETS by the DOR and DSR registers will not
change the previously set parameters to their
default values. All "hardware" RESET from the
RESET pin will set the LOCK bit to logic "0" and
return the EFIFO, FIFOTHR, and PRETRK to
their default values. A status byte is returned
immediately after issuing a LOCK command.
相關PDF資料
PDF描述
FDC37C666GT High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers
FDC37C67X ENHANCED SUPER I/O CONTROLLER WITH FAST IR
FDC37C957FR ULTRA I/O CONTROLLER FOR PORTABLE APPLICATIONS
FDC37M600 ENHANCED SUPER I/O CONTROLLER WITH INFRARED SUPPORT
FDC37M601 ENHANCED SUPER I/O CONTROLLER WITH INFRARED SUPPORT
相關代理商/技術參數
參數描述
FDC37C665GT_07 制造商:SMSC 制造商全稱:SMSC 功能描述:High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers
FDC37C665GT-MS 功能描述:輸入/輸出控制器接口集成電路 Super I/O Controller- Pb Free RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
FDC37C665GTQFP 功能描述:輸入/輸出控制器接口集成電路 Super I/O Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
FDC37C665IR 制造商:SMSC 制造商全稱:SMSC 功能描述:3/5 Volt Advanced High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controller with Infranred Support
FDC37C665IRQFP 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:SMSC 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*