參數資料
型號： FDC37C665GT
廠商： STANDARD MICROSYSTEMS CORP
元件分類： 存儲控制器/管理單元
英文描述： High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers
中文描述： 1 Mbps, IDE COMPATIBLE, FLOPPY DISK DRIVE CONTROLLER, PQFP100
封裝： QFP-100
文件頁數： 62/162頁
文件大?。?/td> 562K
代理商： FDC37C665GT
62
Table 26 - Result Phase Table
FINAL SECTOR
TRANSFERRED TO
HOST
MT
HEAD
ID INFORMATION AT RESULT PHASE
C
NC
C + 1
NC
C + 1
NC
NC
NC
C + 1
H
NC
NC
NC
NC
NC
LSB
NC
LSB
R
N
NC
NC
NC
NC
NC
NC
NC
NC
0
0
Less than EOT
Equal to EOT
Less than EOT
Equal to EOT
Less than EOT
Equal to EOT
Less than EOT
Equal to EOT
R + 1
01
R + 1
01
R + 1
01
R + 1
01
1
1
0
1
NC: No Change, the same value as the one at the beginning of command execution.
LSB: Least Significant Bit, the LSB of H is complemented.
Write Data
After the Write Data command has been issued,
the FDC loads the head (if it is in the unloaded
state), waits the specified head load time if
unloaded (defined in the Specify command),
and begins reading ID fields. When the sector
address read from the diskette matches the
sector address specified in the command, the
FDC reads the data from the host via the FIFO
and writes it to the sector's data field.
After writing data into the current sector, the
FDC computes the CRC value and writes it into
the CRC field at the end of the sector transfer.
The Sector Number stored in "R" is incremented
by one, and the FDC continues writing to the
next data field. The FDC continues this "Multi-
Sector Write Operation". Upon receipt of a
terminal count signal or if a FIFO over/under run
occurs while a data field is being written, then
the remainder of the data field is filled with
zeros.
The FDC reads the ID field of each sector and
checks the CRC bytes. If it detects a CRC error
In one of the ID fields, it sets the IC code in
Status
Register
0
termination), sets the DE bit of Status Register 1
to "1", and terminates the Write Data command.
to
"01"
(abnormal
The Write Data command operates in much the
same manner as the Read Data command. The
following items are the same. Please refer to
the Read Data Command for details:
Transfer Capacity
EN (End of Cylinder) bit
ND (No Data) bit
Head Load, Unload Time Interval
ID information when the host terminates the
command
Definition of DTL when N = 0 and when N
does not = 0
Write Deleted Data
This command is almost the same as the Write
Data command except that a Deleted Data
Address Mark is written at the beginning of the
Data Field instead of the normal Data Address
Mark. This command is typically used to mark
相關PDF資料
PDF描述
FDC37C666GT High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers
FDC37C67X ENHANCED SUPER I/O CONTROLLER WITH FAST IR
FDC37C957FR ULTRA I/O CONTROLLER FOR PORTABLE APPLICATIONS
FDC37M600 ENHANCED SUPER I/O CONTROLLER WITH INFRARED SUPPORT
FDC37M601 ENHANCED SUPER I/O CONTROLLER WITH INFRARED SUPPORT
相關代理商/技術參數
參數描述
FDC37C665GT_07 制造商:SMSC 制造商全稱:SMSC 功能描述:High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers
FDC37C665GT-MS 功能描述:輸入/輸出控制器接口集成電路 Super I/O Controller- Pb Free RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
FDC37C665GTQFP 功能描述:輸入/輸出控制器接口集成電路 Super I/O Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
FDC37C665IR 制造商:SMSC 制造商全稱:SMSC 功能描述:3/5 Volt Advanced High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controller with Infranred Support
FDC37C665IRQFP 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:SMSC 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*