- 您現在的位置：買賣IC網 > PDF目錄381841 > FDC37C665GT (STANDARD MICROSYSTEMS CORP) High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers PDF資料下載
參數資料
| 型號： | FDC37C665GT |
| 廠商： | STANDARD MICROSYSTEMS CORP |
| 元件分類： | 存儲控制器/管理單元 |
| 英文描述： | High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers |
| 中文描述： | 1 Mbps, IDE COMPATIBLE, FLOPPY DISK DRIVE CONTROLLER, PQFP100 |
| 封裝： | QFP-100 |
| 文件頁數： | 66/162頁 |
| 文件大?。?/td> | 562K |
| 代理商： | FDC37C665GT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁當前第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁
66
CONTROL COMMANDS
Control commands differ from the other
commands in that no data transfer takes place.
Three commands generate an interrupt when
complete: Read ID, Recalibrate, and Seek. The
other control commands do not generate an
interrupt.
Read ID
The Read ID command is used to find the
present position of the recording heads. The
FDC stores the values from the first ID field it is
able to read into its registers. If the FDC does
not find an ID address mark on the diskette after
the second occurrence of a pulse on the
nINDEX pin, it then sets the IC code in Status
Register 0 to "01" (abnormal termination), sets
the MA bit in Status Register 1 to "1", and
terminates the command.
The following commands will generate an
interrupt upon completion. They do not return
any result bytes. It is highly recommended that
control commands be followed by the Sense
Interrupt Status command. Otherwise, valuable
interrupt status information will be lost.
Recalibrate
This command causes the read/write head
within the FDC to retract to the track 0 position.
The FDC clears the contents of the PCN
counter and checks the status of the nTR0 pin
from the FDD. As long as the nTR0 pin is low,
the DIR pin remains 0 and step pulses are
issued. When the nTR0 pin goes high, the SE
bit in Status Register 0 is set to "1" and the
command is terminated. If the nTR0 pin is still
low after 79 step pulses have been issued, the
FDC sets the SE and the EC bits of Status
Register 0 to "1" and terminates the command.
Disks capable of handling more than 80 tracks
per side may require more than one Recalibrate
command to return the head back to physical
Track 0.
The Recalibrate command does not have a
result phase. The Sense Interrupt Status
command must be issued after the Recalibrate
command to effectively terminate it and to
provide verification of the head position (PCN).
During the command phase of the recalibrate
operation, the FDC is in the BUSY state, but
during the execution phase it is in a NON-BUSY
state. At this time, another Recalibrate
command may be issued, and in this manner
parallel Recalibrate operations may be done on
up to four drives at once.
Upon power up, the software must issue a
Recalibrate command to properly initialize all
drives and the controller.
Seek
The read/write head within the drive is moved
from track to track under the control of the Seek
command. The FDC compares the PCN, which
is the current head position, with the NCN and
performs the following operation if there is a
difference:
PCN < NCN: Direction signal to drive set to
"1" (step in) and issues
step pulses.
PCN > NCN: Direction signal to drive set to
"0" (step out) and issues
step pulses.
The rate at which step pulses are issued is
controlled by SRT (Stepping Rate Time) in the
Specify command. After each step pulse is
issued, NCN is compared against PCN, and
when NCN = PCN the SE bit in Status Register
0 is set to "1" and the command is terminated.
During the command phase of the seek or
recalibrate operation, the FDC is in the BUSY
state, but during the execution phase it is in the
NON-BUSY state. At this time, another Seek or
Recalibrate command may be issued, and in
this manner, parallel seek operations may be
done on up to four drives at once.
相關PDF資料 |
PDF描述 |
|---|---|
| FDC37C666GT | High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers |
| FDC37C67X | ENHANCED SUPER I/O CONTROLLER WITH FAST IR |
| FDC37C957FR | ULTRA I/O CONTROLLER FOR PORTABLE APPLICATIONS |
| FDC37M600 | ENHANCED SUPER I/O CONTROLLER WITH INFRARED SUPPORT |
| FDC37M601 | ENHANCED SUPER I/O CONTROLLER WITH INFRARED SUPPORT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FDC37C665GT_07 | 制造商:SMSC 制造商全稱:SMSC 功能描述:High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controllers |
| FDC37C665GT-MS | 功能描述:輸入/輸出控制器接口集成電路 Super I/O Controller- Pb Free RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| FDC37C665GTQFP | 功能描述:輸入/輸出控制器接口集成電路 Super I/O Controller RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| FDC37C665IR | 制造商:SMSC 制造商全稱:SMSC 功能描述:3/5 Volt Advanced High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controller with Infranred Support |
| FDC37C665IRQFP | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:SMSC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。