- 您現在的位置：買賣IC網 > PDF目錄1917 > DSP56301VF100 (Freescale Semiconductor)IC DSP 24BIT FIXED-POINT 252-BGA PDF資料下載
參數資料
| 型號： | DSP56301VF100 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 7/124頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DSP 24BIT FIXED-POINT 252-BGA |
| 產品變化通告： | DSP56301 Discontinuation 12/Nov/2009 |
| 標準包裝： | 60 |
| 系列： | DSP563xx |
| 類型： | 定點 |
| 接口： | 主機接口，SSI，SCI |
| 時鐘速率： | 100MHz |
| 非易失內存： | ROM（9 kB） |
| 芯片上RAM： | 24kB |
| 電壓 - 輸入/輸出： | 3.30V |
| 電壓 - 核心： | 3.30V |
| 工作溫度： | -40°C ~ 100°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 252-BGA |
| 供應商設備封裝： | 252-MAPBGA（21x21） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁
DSP56301 Technical Data, Rev. 10
4-2
Freescale Semiconductor
Design Considerations
If the temperature of the package case (TT) is determined by a thermocouple, thermal resistance is
computed from the value obtained by the equation (TJ – TT)/PD.
As noted earlier, the junction-to-case thermal resistances quoted in this data sheet are determined using the first
definition. From a practical standpoint, that value is also suitable to determine the junction temperature from a case
thermocouple reading in forced convection environments. In natural convection, the use of the junction-to-case
thermal resistance to estimate junction temperature from a thermocouple reading on the case of the package will
yield an estimate of a junction temperature slightly higher than actual temperature. Hence, the new thermal metric,
thermal characterization parameter or
Ψ
JT, has been defined to be (TJ – TT)/PD. This value gives a better estimate
of the junction temperature in natural convection when the surface temperature of the package is used. Remember
that surface temperature readings of packages are subject to significant errors caused by inadequate attachment of
the sensor to the surface and to errors caused by heat loss to the sensor. The recommended technique is to attach a
40-gauge thermocouple wire and bead to the top center of the package with thermally conductive epoxy.
4.2 Electrical Design Considerations
Use the following list of recommendations to ensure correct DSP operation.
Provide a low-impedance path from the board power supply to each VCC pin on the DSP and from the
board ground to each GND pin.
Use at least six 0.01–0.1
μF bypass capacitors positioned as close as possible to the four sides of the
package to connect the VCC power source to GND.
Ensure that capacitor leads and associated printed circuit traces that connect to the chip VCC and GND pins
are less than 0.5 inch per capacitor lead.
Use at least a four-layer PCB with two inner layers for VCC and GND.
Because the DSP output signals have fast rise and fall times, PCB trace lengths should be minimal. This
recommendation particularly applies to the address and data buses as well as the IRQA, IRQB, IRQC, IRQD,
TA
, and BG pins. Maximum PCB trace lengths on the order of 6 inches are recommended.
Consider all device loads as well as parasitic capacitance due to PCB traces when you calculate
capacitance. This is especially critical in systems with higher capacitive loads that could create higher
transient currents in the VCC and GND circuits.
All inputs must be terminated (that is, not allowed to float) by CMOS levels except for the three pins with
internal pull-up resistors (TRST, TMS, DE).
Take special care to minimize noise levels on the VCCP, GNDP, and GNDP1 pins.
The following pins must be asserted after power-up: RESET and TRST.
CAUTION
This device contains protective circuitry to
guard against damage due to high static
voltage or electrical fields. However, normal
precautions are advised to avoid application
of any voltages higher than maximum rated
voltages
to
this
high-impedance
circuit.
Reliability of operation is enhanced if unused
inputs are tied to an appropriate logic voltage
level (for example, either GND or VCC).
相關PDF資料 |
PDF描述 |
|---|---|
| DSP56303VL100B1 | IC DSP 24BIT 100MHZ 196-BGA |
| DSP56311VF150B1 | IC DSP 24BIT 150MHZ 196-BGA |
| DSP56321VF200R2 | IC DSP 24BIT 200MHZ 196-BGA |
| DSP56852VFE | IC DSP 16BIT 120MHZ 81-MAPBGA |
| DSP56854FGE | IC DSP 16BIT 120MHZ 128-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DSP56301VF80 | 功能描述:數字信號處理器和控制器 - DSP, DSC MAP DSP RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| DSP56301VF80B1 | 功能描述:數字信號處理器和控制器 - DSP, DSC DSP56301VF80B1 RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| DSP56301VL100 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:24-Bit Digital Signal Processor |
| DSP56301VL80 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:24-Bit Digital Signal Processor |
| DSP56302 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:DSP56301 Digital Signal Processor |
發布緊急采購，3分鐘左右您將得到回復。