參數資料
型號： COP8CCR9LVA8
廠商： National Semiconductor
文件頁數： 71/111頁
文件大?。?/td> 0K
描述： IC MCU EEPROM 8BIT 68-PLCC
標準包裝： 18
系列： COP8™ 8C
核心處理器： COP8
芯體尺寸： 8-位
速度： 20MHz
連通性： Microwire/Plus（SPI），UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 59
程序存儲器容量： 32KB（32K x 8）
程序存儲器類型： 閃存
RAM 容量： 1K x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 5.5 V
數據轉換器： A/D 16x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 68-LCC（J 形引線）
包裝： 管件
其它名稱： *COP8CCR9LVA8
SNOS535I – OCTOBER 2000 – REVISED MARCH 2013
5.13.3 ASSOCIATED I/O PINS
Data is transmitted on the TDX pin and received on the RDX pin. TDX is the alternate function assigned to
Port L pin L2; it is selected by setting ETDX (in the ENUI register) to one. RDX is an inherent function Port
L pin L3, requiring no setup. Port L pin L2 must be configured as an output in the Port L Configuration
Register in order to be used as the TDX pin.
The baud rate clock for the USART can be generated on-chip, or can be taken from an external source.
Port L pin L1 (CKX) is the external clock I/O pin. The CKX pin can be either an input or an output, as
determined by Port L Configuration and Data registers (Bit 1). As an input, it accepts a clock signal which
may be selected to drive the transmitter and/or receiver. As an output, it presents the internal Baud Rate
Generator output.
NOTE
The CKX pin is unavailable if Port L1 is used for the Low Speed Oscillator.
5.13.4 USART OPERATION
The USART has two modes of operation: asynchronous mode and synchronous mode.
5.13.4.1 Asynchronous Mode
This mode is selected by resetting the SSEL (in the ENUI register) bit to zero. The input frequency to the
USART is 16 times the baud rate.
The TSFT and TBUF registers double-buffer data for transmission. While TSFT is shifting out the current
character on the TDX pin, the TBUF register may be loaded by software with the next byte to be
transmitted. When TSFT finishes transmitting the current character the contents of TBUF are transferred
to the TSFT register and the Transmit Buffer Empty Flag (TBMT in the ENU register) is set. The TBMT
flag is automatically reset by the USART when software loads a new character into the TBUF register.
There is also the XMTG bit which is set to indicate that the USART is transmitting. This bit gets reset at
the end of the last frame (end of last Stop bit). TBUF is a read/write register.
The RSFT and RBUF registers double-buffer data being received. The USART receiver continually
monitors the signal on the RDX pin for a low level to detect the beginning of a Start bit. Upon sensing this
low level, it waits for half a bit time and samples again. If the RDX pin is still low, the receiver considers
this to be a valid Start bit, and the remaining bits in the character frame are each sampled a three times
around the center of the bit time. Serial data input on the RDX pin is shifted into the RSFT register. Upon
receiving the complete character, the contents of the RSFT register are copied into the RBUF register and
the Received Buffer Full Flag (RBFL) is set. RBFL is automatically reset when software reads the
character from the RBUF register. RBUF is a read only register. There is also the RCVG bit which is set
high when a framing error or a break detect occurs and goes low once RDX goes high.
5.13.4.2 Synchronous Mode
In this mode data is transferred synchronously with the clock. Data is transmitted on the rising edge and
received on the falling edge of the synchronous clock.
This mode is selected by setting SSEL bit in the ENUI register. The input frequency to the USART is the
same as the baud rate.
When an external clock input is selected at the CKX pin, data transmit and receive are performed
synchronously with this clock through TDX/RDX pins.
If data transmit and receive are selected with the CKX pin as clock output, the device generates the
synchronous clock output at the CKX pin. The internal baud rate generator is used to produce the
synchronous clock. Data transmit and receive are performed synchronously with this clock.
62
Functional Description
Copyright 2000–2013, Texas Instruments Incorporated
Product Folder Links: COP8CBR9 COP8CCR9 COP8CDR9
相關PDF資料
PDF描述
C8051F581-IQ IC 8051 MCU 128K FLASH 48-QFP
C8051F584-IQ IC 8051 MCU 96K FLASH 48-QFP
EFM32TG210F32 MCU 32BIT 32KB FLASH 32-QFN
MPC565CZP56 IC MPU 32BIT IM FLASH 388-PBGA
C8051F587-IQ IC 8051 MCU 96K FLASH 32-QFP
相關代理商/技術參數
參數描述
COP8CDE9 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS Flash Microcontroller with 8k Memory, Virtual EEPROM, 10-Bit A/D and Brownout Reset
COP8CDE9HLQ7 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS Flash Microcontroller with 8k Memory, Virtual EEPROM, 10-Bit A/D and Brownout Reset
COP8CDE9HLQ9 功能描述:IC MCU FLASH 8BIT 8K A/D 44LLP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:COP8™ 8C 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
COP8CDE9HVA7 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS Flash Microcontroller with 8k Memory, Virtual EEPROM, 10-Bit A/D and Brownout Reset
COP8CDE9HVA9 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS Flash Microcontroller with 8k Memory, Virtual EEPROM, 10-Bit A/D and Brownout Reset
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*