- 您現在的位置：買賣IC網 > PDF目錄17021 > CDB5534U (Cirrus Logic Inc)EVAL BOARD FOR CS5534 PDF資料下載
參數資料
| 型號： | CDB5534U |
| 廠商： | Cirrus Logic Inc |
| 文件頁數： | 25/43頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR CS5534 |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 24 |
| 采樣率（每秒）： | 3.84k |
| 數據接口： | 串行 |
| 輸入范圍： | 0 ~ 2.5 V |
| 在以下條件下的電源（標準）： | 35mW @ 5V |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | CS5534 |
| 已供物品： | 板，纜線，CD |
| 相關產品： | CS5534-BSZR-ND - IC ADC 24BIT 4CH W/LNA 24SSOP CS5534-ASZR-ND - IC ADC 24BIT 4CH W/LNA 24-SSOP 598-1116-5-ND - IC ADC 24BIT 4CH W/LNA 24SSOP 598-1115-5-ND - IC ADC 24BIT 4CH W/LNA 20SSOP |
| 其它名稱： | 598-1016 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
CS5531/32/33/34-AS
DS289F5
31
2.5.4. Performing Calibrations
To perform a calibration, the user must send a com-
mand byte with its MSB = 1, its pointer bits
(CSRP2-CSRP0) set to address the desired Setup to
calibrate, and the appropriate calibration bits (CC2-
CC0) set to choose the type of calibration to be per-
formed. Note that calibration assumes that the
CSRs have been previously initialized because the
information concerning the physical channel, its
filter rate, gain range, and polarity, comes from the
channel-setup register addressed by the pointer bits
in the command byte. Once the CSRs are initial-
ized, a calibration can be performed with one com-
mand byte.
The length of time it takes to do a calibration is
slightly less than the amount of time it takes to do
a single conversion (see Table 1 for single conver-
sion timing). Offset calibration takes 608 clock cy-
cles less than a single conversion when FRS = 0,
and 729 clock cycles less when FRS = 1. Gain cal-
ibration takes 128 clock cycles less than a single
conversion when FRS = 0, and 153 clock cycles
less when FRS = 1.
Once a calibration cycle is complete, SDO falls and
the results are automatically stored in either the
gain or offset register for the physical channel be-
ing calibrated when the OGS bit in the Configura-
tion Register is set to ‘0’. If the OGS bit is set to ‘1’,
the results will be stored in the register specified by
the OG1-OG0 bits of the selected Setup. See the
OGS bit description for more details (Section
2.3.7). SDO will remain low until the next com-
mand word is begun. If additional calibrations are
performed while referencing the same calibration
registers, the last calibration results will replace the
effects from the previous calibration as only one
offset and gain register is available per physical
channel. Only one calibration is performed with
each command byte. To calibrate all the channels,
additional calibration commands are necessary.
2.5.5. Self-calibration
The CS5531/32/33/34 offer both self-offset and
self-gain calibrations. For the self-calibration of
offset, the converters internally tie the inputs of the
1x amplifier together and routes them to the AIN-
pin as shown in Figure 11. For accurate self calibra-
tion of offset to occur, the AIN pins must be at the
proper common-mode voltage as specified in the
Analog Characteristics section. Self-offset calibra-
tion uses the 1x gain amplifier, and is therefore not
valid in the 2x-64x gain ranges. A self-offset calibra-
tion of these gain ranges can be performed by setting
the IS bit in the configuration register to a ‘1’, and
performing a system offset calibration. The IS bit
must be returned to ‘0’ afterwards for normal opera-
tion of the device.
For self calibration of gain, the differential inputs
of the modulator are connected to VREF+ and
VREF- as shown in Figure 12. Self calibration of
gain will not work with (VREF+ - VREF-) > 2.5V.
Self calibration of gain is performed in the
GAIN = 1x mode without regard to the setup regis-
ter’s gain setting. Gain errors in the PGIA gain
steps 2x to 64x are not calibrated as this would re-
quire an accurate low-voltage source other than the
reference voltage. A system calibration of gain
should be performed if accurate gains are to be
achieved on the ranges other than 1x, or when
(VREF+ – VREF-) > 2.5V.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9648-125EBZ | EVAL BOARD AD9648-125 |
| CDB5463U-Z | EVAL BOARD USB FOR CS5463 |
| AD9633-125EBZ | BOARD EVAL FOR AD9633 |
| PM0805-68NK-RC | INDUCTOR CHIP 68NH 10% SMD |
| MAX1379EVKIT+ | EVAL KIT FOR MAX1379 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CDB5534U-Z | 功能描述:EVAL BD 24-BIT ADCS W/ULTRALN PG 制造商:cirrus logic inc. 系列:- 零件狀態:在售 A/D 轉換器數:1 位數:24 采樣率（每秒）:3.84k 數據接口:串行 輸入范圍:±2.5 V 不同條件下的功率（典型值）:35mW @ 3.84kSPS 使用的 IC/零件:CS5534 所含物品:板，電纜 標準包裝:1 |
| CDB5540 | 制造商:Cirrus Logic 功能描述:EVAL BOARD FOR CS5540 - Bulk |
| CDB5541 | 制造商:Cirrus Logic 功能描述:EVAL BOARD FOR 5540 & 5541 N/A - Bulk 制造商:Cirrus Logic 功能描述:Tools Development kit For Use |
| CDB5550 | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:Evaluation Board and Software |
| CDB5560 | 功能描述:數據轉換 IC 開發工具 Eval Bd 50kSps 24Bit Mux ADC RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
發布緊急采購，3分鐘左右您將得到回復。