- 您現在的位置：買賣IC網 > PDF目錄366549 > AM79C864AKCW (ADVANCED MICRO DEVICES INC) Physical Layer Controller With Scrambler (PLC-S) PDF資料下載
參數資料
| 型號： | AM79C864AKCW |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Physical Layer Controller With Scrambler (PLC-S) |
| 中文描述： | 1 CHANNEL(S), 100M bps, FDDI CONTROLLER, PQFP120 |
| 封裝： | PLASTIC, QFP-120 |
| 文件頁數： | 19/51頁 |
| 文件大?。?/td> | 271K |
| 代理商： | AM79C864AKCW |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
AMD
P R E L I M I N A R Y
3-21
Am79C864A
Table 3. PLC_CNTRL_B (continued)
Bit
Name
Definition
07
CLASS_S
When CLASS_S is set, signifying that the PHY is a single attach station, the station will
not be bypassed before the PCM gets to the ACTIVE state. Note that this bit has effect
when the PCM is in normal operation. When the PCM is in the MAINT state, the
REQ_SCRUB and SC_BYPASS bits in the PLC_CNTRL_A register control the
bypass operation. This bit can only be changed when the PCM is in the OFF state. If
this bit is written when the PCM is in any other state, the change will be ignored.
06–05
PC_LOOP
PC_LOOP controls the loopback used in the Link Confidence Test (LCT). When it is
set to a value other than zero and the PCM is in the NEXT state, the PCM will perform
the LCT in one of three ways. The following table describes the action taken according
to the value of the two bits:
PC_LOOP
00
01
Description
No LCT is performed
The PCM asserts Transmit PDR. This assumes that Protocol
Data Units (PDUs) will be input at TX(9–0).
The PCM asserts Transmit Idle. This causes the PLC-S to source
Idle symbols.
The PCM asserts Transmit PDR and sets up a remote loopback
path in the PLC-S.
PC_LOOP should only be written after the PCM_CODE interrupt has been generated.
If the PCM is not in the NEXT state, or if PCM_SIGNALING is set, then any value
written to this field will be ignored. Once PC_LOOP has been written, it must be
cleared and then written again to perform another LCT.
10
11
04
PC_JOIN
When PC_JOIN is set and the PCM is in the NEXT state, the PCM will transition to the
JOIN state and the PCM join sequence will be started. PC_JOIN should only be written
after the PCM_CODE interrupt has been generated. If the PCM is not in the NEXT
state or if PCM_SIGNALING is set, then any value written to this field will be ignored.
After this bit is set, it must be cleared and then set again to cause another transition
from the NEXT state to the JOIN state. Note that if PC_JOIN is set after the LCT has
been started but before it has completed, then the LCT will be aborted and the PCM join
sequence started.
03
LONG
When LONG is set, the PCM will perform a long LCT; that is, it will continue the test until the
processor issues a PC_SIGNAL (i.e., a write to XMIT_VECTOR register), PC_JOIN, or other
command. Otherwise it will perform a LCT, that is, it will stop the test after the length of time
indicated in the LC_LENGTH register. In either case LCT will stop whenever Master Line State
or Halt Line State is detected, indicating that the neighboring station has completed its
LCT and has started signaling.
02
PC_MAINT
When PC_MAINT is set, the PCM state machine transitions to the MAINT state if it is
currently in the OFF state. If the PCM is not in the OFF state when this bit is written, and
subsequently transitions to the OFF state, it will immediately transition to the MAINT
state.
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C873 | NetPHY⑩ -1 10/100 Mbps Ethernet Physical Layer Single-Chip Transceiver with 100BASE-FX Support |
| AM79C873KCW | NetPHY⑩ -1 10/100 Mbps Ethernet Physical Layer Single-Chip Transceiver with 100BASE-FX Support |
| AM79C874VI | NetPHY-1LP Low Power 10/100-TX/FX Ethernet Transceiver |
| Am79C874 | NetPHY-1LP Low Power 10/100-TX/FX Ethernet Transceiver |
| AM79C874VC | NetPHY-1LP Low Power 10/100-TX/FX Ethernet Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C864KC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Transceiver |
| AM79C870KC/W | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Transceiver |
| AM79C871KC/W | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Transceiver |
| AM79C873 | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:NetPHY⑩ -1 10/100 Mbps Ethernet Physical Layer Single-Chip Transceiver with 100BASE-FX Support |
| AM79C873KCW | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:NetPHY⑩ -1 10/100 Mbps Ethernet Physical Layer Single-Chip Transceiver with 100BASE-FX Support |
發布緊急采購，3分鐘左右您將得到回復。