
[AK4671]
MS0666-E-00
2007/10
- 7 -
ABSOLUTE MAXIMUM RATINGS
(VSS1=VSS2=VSS3=VSS4=0V;
Note 2
,
Note 3
)
Parameter
Power Supplies:
Analog
PLLBT
10bit SAR ADC
Digital
Digital I/O 2
Digital I/O 3
Input Current, Any Pin Except Supplies
Analog Input Voltage 1 (
Note 4
)
Analog Input Voltage 2 (
Note 5
)
Digital Input Voltage 1 (
Note 6
)
Digital Input Voltage 2 (
Note 7
)
Digital Input Voltage 3 (
Note 8
)
Ambient Temperature (powered applied)
Storage Temperature
Note 2. All voltages with respect to ground.
Note 3. VSS1, VSS2, VSS3 and VSS4 must be connected to the same analog ground plane.
Note 4. RIN4/IN4
, LIN4/IN4+, RIN3/IN3
, LIN3/IN3+, RIN2/IN2
, LIN2/IN2+, RIN1/IN1
, LIN1/IN1+ pins
Note 5. SAIN1, SAIN2, SAIN3 pins
Note 6. PDN, I2C, CSN/CAD0, CCLK/SCL, CDTI/SDA, SDTI, LRCK, BICK, MCKI pins
Pull-up resistors at SDA and SCL pins should be connected to (DVDD+0.3)V or less voltage.
Note 7. BICKA, SYNCA, SDTIA pins
Note 8. BICKB, SYNCB, SDTIB pins
WARNING: Operation at or beyond these limits may result in permanent damage to the device.
Normal operation is not guaranteed at these extremes.
RECOMMENDED OPERATING CONDITIONS
(VSS1=VSS2=VSS3=VSS4=0V;
Note 2
)
Parameter
Symbol
Power Supplies
Analog
AVDD
(
Note 9
) PLLBT
PVDD
10bit SAR ADC
SAVDD
Digital
DVDD
Digital I/O 2
TVDD2
Digital I/O 3
TVDD3
Difference
AVDD
PVDD
Note 2. All voltages with respect to ground.
Note 9. The power-up sequence between AVDD, PVDD, SAVDD, DVDD, TVDD2 and TVDD3 is not critical.
The PDN pin should be held to “L” when power-up. The PDN pin should be set to “H” after all power supplies are
powered-up. The AK4671 should be operated by the recommended power-up/down sequence shown in “
System
Design (Grounding and Power Supply Decoupling)
” to avoid pop noise at receiver output, headphone output and
line output.
When the power is OFF partially except for DVDD, all power management bits (PMVCM, PMMP, PMMICL,
PMMICR, PMADL, PMADR, PMDAL, PMDAR, PMPLL, PMLOOPL, PMLOOPR, PMAINL1, PMAINR1,
PMAINL2, PMAINR2, PMAINL3, PMAINR3, PMAINL4, PMAINR4, PMLO1, PMRO1, PMLO2, PMRO2,
PMLO2S, PMRO2S, PMLO3, PMRO3, PMSRA, PMSRB, PMPCM, PMSAD) should be “0” or the PDN pin
should be “L”. DVDD should not be powered OFF while AVDD, PVDD, SAVDD, TVDD2 or TVDD3 is
powered ON. When only DVDD is OFF, the current of 10mA to 100mA around may occur.
* AKEMD assumes no responsibility for the usage beyond the conditions in this datasheet.
Symbol
AVDD
PVDD
SAVDD
DVDD
TVDD2
TVDD3
IIN
VINA1
VINA2
VIND1
VIND2
VIND3
Ta
Tstg
min
0.3
0.3
0.3
0.3
0.3
0.3
-
0.3
0.3
0.3
0.3
0.3
30
65
max
4.0
4.0
4.0
4.0
4.0
4.0
±
10
Units
V
V
V
V
V
V
mA
V
V
V
V
V
°
C
°
C
AVDD+0.3
SAVDD+0.3
DVDD+0.3
TVDD2+0.3
TVDD3+0.3
85
150
min
2.2
2.2
2.2
1.6
1.6
1.6
0.1
typ
3.3
3.3
3.3
3.3
3.3
3.3
0
max
3.6
3.6
3.6
3.6
3.6
3.6
+0.1
Units
V
V
V
V
V
V
V