參數資料
型號: ADS1191IPBSR
廠商: Texas Instruments
文件頁數: 24/67頁
文件大?。?/td> 0K
描述: IC AFE 16BIT 8KSPS 1CH 32TQFP
標準包裝: 1,000
位數: 16
通道數: 1
電壓 - 電源,模擬: 2.7 V ~ 5.25 V
電壓 - 電源,數字: 1.7 V ~ 3.6 V
封裝/外殼: 32-TQFP
供應商設備封裝: 32-TQFP(5x5)
包裝: 帶卷 (TR)
START
DRDY
4 / f
CLK
4 / f
CLK
Data Updating
t
SETTLE
SBAS566A – DECEMBER 2011 – REVISED SEPTEMBER 2012
Single-Shot Mode
The single-shot mode is enabled by setting the SINGLE_SHOT bit in the CONFIG1 register to '1'. In single-shot
mode, the ADS1191/2 perform a single conversion when the START pin is taken high or when the START
opcode command is sent. As seen in Figure 34, when a conversion is complete, DRDY goes low and further
conversions are stopped. Regardless of whether the conversion data are read or not, DRDY remains low. To
begin a new conversion, take the START pin low and then back high, or transmit the START opcode again.
When switching from continuous mode to pulse mode, make sure the START signal is pulsed or issue a STOP
command followed by a START command.
This conversion mode is provided for applications that require non-standard or non-continuous data rates.
Issuing a START command or toggling the START pin high resets the digital filter, effectively dropping the data
rate by a factor of four. Note that this mode leaves the system more susceptible to aliasing effects, requiring
more complex analog anti-aliasing filters at the inputs. Loading on the host processor increases because it must
toggle the START pin or send a START command to initiate a new conversion cycle.
Figure 35. DRDY with No Data Retrieval in Single-Shot Mode
MULTIPLE DEVICE CONFIGURATION
The ADS1191/2 are designed to provide configuration flexibility when multiple devices are used in a system. The
serial interface typically needs four signals: DIN, DOUT, SCLK, and CS. With one additional chip select signal
per device, multiple devices can be connected together. The number of signals needed to interface n devices is
3 + n.
The right leg drive amplifiers can be daisy-chained as explained in the RLD Configuration with Multiple Devices
subsection of the ECG-Specific Functions section. To use the internal oscillator in a daisy-chain configuration,
one of the devices must be set as the master for the clock source with the internal oscillator enabled (CLKSEL
pin = 1) and the internal oscillator clock brought out of the device by setting the CLK_EN register bit to '1'. This
master device clock is used as the external clock source for the other devices.
30
Copyright 2011–2012, Texas Instruments Incorporated
Product Folder Links: ADS1191 ADS1192
相關PDF資料
PDF描述
V375C2M50BF CONVERTER MOD DC/DC 2V 50W
MAX9015AEKA+T IC COMPARATOR SGL SOT23-8
V375C2M50BL2 CONVERTER MOD DC/DC 2V 50W
V375C2M50BL CONVERTER MOD DC/DC 2V 50W
MCP3901A0T-E/ML IC AFE 24BIT 64KSPS 2CH 20QFN
相關代理商/技術參數
參數描述
ADS1191IRSMR 制造商:Texas Instruments 功能描述:AFE General Purpose 1ADC 24-Bit 1.8V/3V 32-Pin VQFN EP T/R 制造商:Texas Instruments 功能描述:IC AFE 16BIT 8KSPS 1CH 32VQFN 制造商:Texas Instruments 功能描述:Low Pwr Int AFE for ECG App
ADS1191IRSMT 功能描述:模數轉換器 - ADC Cmplt Lw Pwr Intgrtd AFE for ECG apps RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
ADS1192 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low-Power, 2-Channel, 16-Bit Analog Front-End for Biopotential Measurements
ADS1192ECG-FE 功能描述:數據轉換 IC 開發工具 ADS1192 Demo Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
ADS1192IPBS 功能描述:模數轉換器 - ADC Low Pwr Integ AFE RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32