參數資料
型號: ADM7008
廠商: Electronic Theatre Controls, Inc.
英文描述: Octal Ethernet 10/100M PHY
中文描述: 八路個10/100M以太網物理層
文件頁數: 23/92頁
文件大?。?/td> 981K
代理商: ADM7008
ADM7008
Interface Description
Pin #
Pin Name
Type
Pin Description
until all the data in the FIFO is presented onto RXD.
CRSDV_P3 is asserted for the duration of carrier activity for a
false carrier event.
Not Used.
Not used in SMII Mode
SS_SMII Receive Synchronization Signal. In SS_SMII Mode,
this pin sets the bit stream alignment of SSS_SMII_RXD for all
ports.
Port 3 RMII Transmit Data. Transmit data for port 3 inputs the
di-bits that re transmitted and are driven synchronously to
REFCLK. Note that in 100Mb/s mode, TXD can change once
per REFCLK cycle, whereas in 10Mb/s mode, TXD must be
held steady for 10 consecutive REFCLK cycles.
Link and Activity LED/Port 3 SMII Transmit Data. TXD0 for port
3 inputs the data that is transmitted and is driven synchronously
to SMII_REFCLK (pin 70). In 100Mb/s mode, TXD0 inputs a
new 10-bit segment starting with SYNC. In 10Mb/s mode,
TXD0 must repeat each 10-bit segment 10 times.
TXD1_P3 acts as Port 3 Link/Activity LED in both SMII and
SS_SMII Mode. See LED Description for more detail.
Link and Activity LED/Port 3 SS_SMII Transmit Data. TXD0 for
port 3 inputs the data that is transmitted and is driven
synchronously to TXCLK (pin 70). In 100Mb/s mode, TXD0
inputs a new 10-bit segment starting with SYNC. In 10Mb/s
mode, TXD0 must repeat each 10-bit segment 10 times.
Port 3 Transmit Enable. Transmit Enable for port 3 indicates
that the di-bit on TXD is valid and it is driven synchronously to
REFCLK.
SMII Synchronization Signal. In SMII Mode, this pin sets the bit
stream alignment of SMII_TXD and SMII_RXD for all ports.
SS_SMII Transmit Synchronization Signal. In SS_SMII Mode,
this pin sets the bit stream alignment of SSS_SMII_TXD for all
ports.
REC_10M: Value on RXD1_P2 will be latched by ADM7008
during power on reset as Port 2 10M Re-command value.
0: Recommend Port 2 to operate in 100M Mode (100M)
1: Recommend Port 2 to operate in 10M Mode
PHY Address Bit 0. Value on RXD1 will be latched by
ADM7008 during power on reset as PHY address bit 0.
Combined with PHYADDR1 (pin 44) to form PHY address for
ADM7008. See PHYADDR1 description for more detail
Port 2 RMII Receive Data. RXD[1:0] are the port 2 output di-
bits synchronously to REFCLK. Upon assertion of CRSDV_P,
RXD0 and RXD1 remain at 00 until valid data is output from the
FIFO
t RXD Th
t t f
lid d t i i di
ADMtek Inc.
2-11
SMII Mode
N/A
SS_SMII Mode
RX_SYNC
84, 85
RMII Mode
TXD[1:0]_P3
SMII Mode
LNKACT_P3,
SMII_TXD_P3
SS_SMII Mode
LNKACT_P3,
SSSMII_TXD_P3
I,
TTL,
PD
86
RMII Mode
TXEN_P3
SMII Mode
SMII_SYNC
SS_SMII Mode
TX_SYNC
I,
TTL
89, 90
Power On
Setting
REC_10M_P2,
PHYADDR0
RMII Mode
RXD[1:0]_P2
I,
PD,
PD
O,
8mA
t d b 01
相關PDF資料
PDF描述
ADM9511 LAN/Modem Controller with Embedded Fast Ethernet PHY
ADS-238Q 12-Bit, 20MHz, Low Power Sampling A/D Converters
ADS-917GC 14-Bit, 1MHz, Low-Power Sampling A/D Converters
ADS-927GC 14-Bit, 1MHz, Low-Power Sampling A/D Converters
ADS-927GM 14-Bit, 1MHz, Low-Power Sampling A/D Converters
相關代理商/技術參數
參數描述
ADM7008A3T1 功能描述:IC SWITCH CTRLR 10/100 128PQFP RoHS:否 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN(6x6) 包裝:* 其它名稱:Q6396337A
ADM7008A3T1NP 制造商:Infineon Technologies AG 功能描述:SWITCH / PHY
ADM7008XA3T1 功能描述:IC SWITCH CTRLR 10/100 128PQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN(6x6) 包裝:* 其它名稱:Q6396337A
adm7008x-a3-t-1 制造商:Rochester Electronics LLC 功能描述: 制造商:Infineon Technologies AG 功能描述:
ADM7008XA3T1XP 制造商:Infineon Technologies AG 功能描述:GREEN, SWITCH / PHY