- 您現在的位置：買賣IC網 > PDF目錄382773 > ZPSD613(V)E1 Field Programmable Microcontroller Peripherals with Embedded Micro--Cell(可編程邏輯，零功耗，4K位SRAM,26個可編程I/O,通用PLD有63個輸入) PDF資料下載
參數資料
| 型號： | ZPSD613(V)E1 |
| 英文描述： | Field Programmable Microcontroller Peripherals with Embedded Micro--Cell(可編程邏輯，零功耗，4K位SRAM,26個可編程I/O,通用PLD有63個輸入) |
| 中文描述： | 現場可編程微控制器外圍設備和嵌入式微-細胞（可編程邏輯，零功耗，4K的位的SRAM，26余個可編程輸入/輸出，通用PLD的有63個輸入） |
| 文件頁數： | 94/98頁 |
| 文件大小： | 484K |
| 代理商： | ZPSD613(V)E1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁當前第94頁第95頁第96頁第97頁第98頁
ZPSD6XX(V) Family
12-94
Symbol
Parameter
1
Conditions Typical
2
Max
Unit
C
IN
C
OUT
C
VPP
Capacitance (for input pins only)
V
IN
= 0 V
V
OUT
= 0 V
V
PP
= 0 V
4
6
pF
Capacitance (for input/output pins)
8
12
pF
Capacitance (for WR/V
PP
or R/W/V
PP
)
18
25
pF
NOTES:
1. These parameters are only sampled and are not 100% tested.
2. Typical values are for T
A
= 25°C and nominal supply voltages.
T
A
= 25 °C, f = 1 MHz
Pin Capacitance
Figure 44.
AC Testing
Input/Output
Waveform
Figure 45.
AC Testing
Load Circuit
Erasure and
Programming
3.0V
0V
TEST POINT
1.5V
DEVICE
UNDER TEST
2.01 V
195
C
L
= 30 pF
(INCLUDING
SCOPE AND JIG
CAPACITANCE)
To clear all locations of their programmed contents, expose the window packaged device
to an ultra-violet light source. A dosage of 30 W second/cm
2
is required. This dosage can
be obtained with exposure to a wavelength of 2537 and intensity of 12000 μW/cm
2
for 40
to 45 minutes. The device should be about 1 inch from the source, and all filters should be
removed from the UV light source prior to erasure. OTP products are programmed once
and cannot be erased.
The ZPSD6XX(V) and similar devices will erase with light sources having wavelengths
shorter than 4000 . Although the erasure times will be much longer than with UV sources
at 2537 , exposure to fluorescent light and sunlight eventually erases the device.
For maximum system reliability, these sources should be avoided. If used in such an
environment, the package windows should be covered by an opaque substance.
Upon delivery from WSI, or after each erasure, the ZPSD6XX(V) device has all bits in the
PAD and EPROM in the “1” or high state. The configuration bits are in the “0” or low
state. The code, configuration, and PAD MAP data are loaded through the procedure of
programming
Information for programming the device is available directly from WSI. Please contact your
local sales representative.
相關PDF資料 |
PDF描述 |
|---|---|
| ZPSD813F1V | Flash In System Programmable Mirocomputer Peripherals(閃速，在系統可編程微控制器外圍器件，1M位閃速存儲器，256K位EEPROM，16K位SRAM) |
| ZR33771GC-40 | Cell Rectifier Diodes |
| ZR33771GM-20 | Cell Rectifier Diodes |
| ZR33771GM-30 | Cell Rectifier Diodes |
| ZR33771GM-40 | Cell Rectifier Diodes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ZPSD701S5-70J | 制造商:WSI 功能描述: |
| ZPSD701S5-70L | 制造商:WSI 功能描述: |
| ZPSD813F1-12JI | 制造商:WSI 功能描述: |
| ZPSD813F1-15J | 制造商:WSI 功能描述: |
| ZPSD813F1-15U | 制造商:WSI 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。