- 您現在的位置：買賣IC網 > PDF目錄10009 > XRT83SL30IVTR-F (Exar Corporation)IC LIU T1/E1/J1 SGL 64TQFP PDF資料下載
參數資料
| 型號： | XRT83SL30IVTR-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 6/76頁 |
| 文件大小： | 0K |
| 描述： | IC LIU T1/E1/J1 SGL 64TQFP |
| 標準包裝： | 1,000 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 1/1 |
| 規程： | T1，E1，J1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-TQFP（10x10） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
XRT83SL30
11
SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
REV. 1.0.1
REDUNDANCY SUPPORT
SIGNAL NAME
PIN #
TYPE
DESCRIPTION
DMO
11
O
Driver Failure Monitor
This pin transitions "High" if a short circuit condition is detected in the trans-
mit driver, or no transmit output pulse is detected for more than 128 TCLK
cycles.
TERMINATIONS
SIGNAL NAME
PIN #
TYPE
DESCRIPTION
GAUGE
49
I
Twisted Pair Cable Wire Gauge Select
In Hardware Mode, connect this pin "High" to select 26 Gauge wire. Connect this pin
“Low” to select 22 and 24 gauge wire.
NOTE: Internally pulled “Low” with a 50k
resistor.
TRATIO
26
I
Transmitter Transformer Ratio Select
In Hardware Mode, in external termination mode (TXTSEL = “0”), setting this pin "High"
selects a transformer ratio of 1:2 for the transmitter. A "Low" on this pin sets the transmit-
ter transformer ratio to 1:2.45. In the internal termination mode the transmitter trans-
former ratio is permanently set to 1:2 and the state of this pin is ignored.
NOTE: Internally pulled "Low" with a 50k
resistor.
RXTSEL
44
I
Receiver Termination Select
In Hardware Mode when this pin is “Low” the receive line termination is determined only
by the external resistor. When “High”, the receive termination is realized by internal
resistors or the combination of internal and external resistors according to RXRES[1:0].
These conditions are described in the following table:
In Host Mode bit 7 in Control Register 1 (01h) determines if the if the receiver termina-
tion is external or internal. The function of RXTSEL can be transferred to the harware pin
by setting TERCNTL bit (bit 4)
NOTE: This pin is internally pulled "Low" with a 50k
resistor.
TXTSEL
45
I
Transmit Termination Select
In Hardware Mode when this pin is “Low” the transmit line termination is determined
only by external resistor. When “High”, the transmit termination is realized only by an
internal resistor. These conditions are summarized in the following table:
NOTE: This pin is internally pulled "Low" with a 50k
resistor.
RXTSEL
RX Termination
0
1
External
Internal
TXTSEL
TX Termination
0
1
External
Internal
相關PDF資料 |
PDF描述 |
|---|---|
| XRT7298IWTR | IC LINE TX DS3/STS-1 E3 28SOJ |
| VE-BNT-MX-B1 | CONVERTER MOD DC/DC 6.5V 75W |
| VE-BNP-MX-B1 | CONVERTER MOD DC/DC 13.8V 75W |
| LTC1334CNW | IC CMOS TXRX MULTIPROTOCOL 28DIP |
| VE-BNN-MX-B1 | CONVERTER MOD DC/DC 18.5V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT83SL314 | 制造商:EXAR 制造商全稱:EXAR 功能描述:14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83SL314_05 | 制造商:EXAR 制造商全稱:EXAR 功能描述:14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83SL314ES | 功能描述:LIN 收發器 14 CHT1/E1 LIUSH RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| XRT83SL314IB | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT83SL314IB-F | 功能描述:LIN 收發器 RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
發布緊急采購，3分鐘左右您將得到回復。