REV. 1.0.7 8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT monitor the 16-bit LCV counter by programming the appropriate global " />
參數資料
型號： XRT83SH38IB-F
廠商： Exar Corporation
文件頁數： 22/78頁
文件大?。?/td> 0K
描述： IC LIU SH T1/E1/J1 8CH 225BGA
標準包裝： 84
類型： 線路接口裝置（LIU）
驅動器/接收器數： 8/8
規程： T1，E1，J1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 225-BGA
供應商設備封裝： 225-BGA（19x19）
包裝： 托盤
XRT83SH38
26
REV. 1.0.7
8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
monitor the 16-bit LCV counter by programming the appropriate global register, the LCV/OFD will be set to a
"1" if the counter saturates.
3.3
Receive Jitter Attenuator
The receive path has a dedicated jitter attenuator that reduces phase and frequency jitter in the recovered
clock. The jitter attenuator uses a data FIFO (First In First Out) with a programmable depth of 32-bit or 64-bit.
If the LIU is used for line synchronization (loop timing systems), the JA should be enabled. When the Read
and Write pointers of the FIFO are within 2-Bits of over-flowing or under-flowing, the bandwidth of the jitter
attenuator is widened to track the short term input jitter, thereby avoiding data corruption. When this condition
occurs, the jitter attenuator will not attenuate input jitter until the Read/Write pointer’s position is outside the 2-
Bit window. In T1 mode, the bandwidth of the JA is always set to 3Hz. In E1 mode, the bandwidth is
programmable to either 10Hz or 1.5Hz (1.5Hz automatically selects the 64-Bit FIFO depth). The JA has a
clock delay equal to of the FIFO bit depth.
NOTE: If the LIU is used in a multiplexer/mapper application where stuffing bits are typically removed, the transmit path has
a dedicated jitter attenuator to smooth out the gapped clock. See the Transmit Section of this datasheet.
3.4
HDB3/B8ZS Decoder
In single rail mode, RPOS can decode AMI or HDB3/B8ZS signals. For E1 mode, HDB3 is defined as any
block of 4 successive zeros replaced with OOOV or BOOV, so that two successive V pulses are of opposite
polarity to prevent a DC component. In T1 mode, 8 successive zeros are replaced with OOOVBOVB. If the
HDB3/B8ZS decoder is selected, the receive path removes the V and B pulses so that the original data is
output to RPOS.
3.5
RPOS/RNEG/RCLK
The digital output data can be programmed to either single rail or dual rail formats. Figure 13 is a timing
diagram of a repeating "0011" pattern in single-rail mode. Figure 14 is a timing diagram of the same fixed
pattern in dual rail mode.
FIGURE 13. SINGLE RAIL MODE WITH A FIXED REPEATING "0011" PATTERN
FIGURE 14. DUAL RAIL MODE WITH A FIXED REPEATING "0011" PATTERN
RCLK
RPOS
00
0
1
RCLK
RPOS
00
0
1
RNEG
相關PDF資料
PDF描述
XRT86L30IV-F IC LIU/FRAMER TI/E1/J1 SGL 128LQ
XRT86VL30IV-F IC FRAMR/LIU T1/E1/J1 QD 128LQFP
XRT86VL32IB-F IC LIU/FRAMER T1/E1/J1 2CH 225BG
XRT86VL34IB-F IC LIU/FRAMER T1/E1/J1 4CH 225BG
XRT86VL38IB484-F IC LIU/FRAMER T1/E1/J1 8CH 484BG
相關代理商/技術參數
參數描述
XRT83SL216 制造商:EXAR 制造商全稱:EXAR 功能描述:16-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT
XRT83SL216_06 制造商:EXAR 制造商全稱:EXAR 功能描述:16-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT
XRT83SL216ES 功能描述:外圍驅動器與原件 - PCI 16 CH E1 LIU SH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT83SL216IB 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
XRT83SL216IB-F 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*