參數資料
型號: XRT82L24AIV-F
廠商: Exar Corporation
文件頁數: 5/39頁
文件大?。?/td> 0K
描述: IC LIU E1 QAUD 100TQFP
標準包裝: 90
類型: 線路接口裝置(LIU)
驅動器/接收器數: 4/4
規程: E1
電源電壓: 3.135 V ~ 3.465 V
安裝類型: 表面貼裝
封裝/外殼: 100-LQFP
供應商設備封裝: 100-TQFP(14x14)
包裝: 托盤
其它名稱: XRT82L24AIV-F-ND
á
XRT82L24A
QUAD E1 LINE TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
REV. 1.1.2
11
consecutive zeros before LOS is declared can be in-
creased to 4096 bits. During extended LOS Mode,
the LOS condition will be cleared when 4096 more
valid data bits are present (when operating in the
Host Mode). The LOS condition is cleared when the
input signal rises above 16dB below 0dB nominal lev-
el and meets 12.5% density of 4 ones in a 32 bit win-
dow with no more than 16 consecutive zeros.
Clock signals generated when LOS is declared
The output signal at the RxClk output pin depends
upon the type of LOS condition that is occurring.
Complete Loss of Signal (Zero Amplitude)
If the XRT 82L24A experiences a complete Loss of
Signal (e.g., no signal amplitude), then the XRT
82L24A Clock Recovery PLL enters the Training
Mode, and Differentially begins to lock onto the signal
applied to the MCLK input pin. As a consequence,
the Clock Recovery PLL will begin to drive a clock
signal to the Terminal Equipment (via the RxClk out-
put pin), which is derived from the MCLK input pin.
Degraded Type of Loss of Signal Event (Non-Zero
Amplitude)
If the XRT 82L24A experiences a degraded type of
LOS event (e.g., where there is still a small amount of
discernible signal amplitude in the line signal, but
small enough to qualify as an LOS event) then the
Clock Recovery PLL could lock onto this degraded
line signal and will subsequently drive the same fre-
quency via the RxClk output pins.
CONDITIONS FOR DECLARING AND CLEARING
LOS IN THE E1 MODE.
Each E1 channel of the XRT 82L24A has two criteria
for LOS Detection, Analog and Digital. A channel
will declare a LOS condition when both of these LOS
Detectors detect an LOS condition.
Analog LOS Detector
The Analog LOS Detector will declare an LOS condi-
tion, if it determines that the amplitude of the incom-
ing line signal has dropped to less than
-15dB (below the nominal pulse amplitude of 3V for
twisted-pair, or 2.37V for coaxial-cable) for at least
32 bit-periods.
The Analog LOS Detector will clear the LOS condi-
tion, if it determines that the incoming line signal is no
more than 12.5dB below the nominal 3V pulse ampli-
tude.
NOTE: The difference in the signal level required to declare
and clear LOS is 2.5dB. This 2.5dB hysteresis is designed
into the Analog LOS Detector circuitry, in order to prevent
chattering in the LOS output pin or bit-field.
Digital LOS Detector
The Digital LOS Detector will declare an LOS condi-
tion, if it detects a string of at least 32 consecutive
"0"s.
The Digital LOS Detector will clear the LOS condition,
if it determines that the incoming E1 line signal has a
pulse density of 12.5% or more without 16 consecu-
tive “0’s” for at least 32 consecutive bit periods.
NOTE: The pulse density requirement of 12.5% accounts
for HDB3 coding.
RECEIVE DATA MUTING
The XRT 82L24A permits the user to “MUTE” the re-
covered data output signals anytime the LOS condi-
tion is declared. If the user invokes this function, then
the RPOS/RDAT and RNEG output pins will be pulled
to GND for the duration that the LOS condition exists.
This feature is useful in that it prevents the LIU from
routing electrical noise (which has been “recovered”
by the Clock Recovery PLL) to the Framer IC and
preventing it from declaring an LOS condition. This
feature is enabled by setting the RXMUTE bit to a “1”
in the Host Mode (Register 1, Bit 2 Location) or by
connecting pin 67 High in the Hardware Mode.
LOOP-BACK MODES
Each channel within the XRT 82L24A can be config-
ured to operate in any of the following loop-back
modes:
Remote Loop-Back Mode
Digital Local Loop-Back Mode
Analog Local Loop-Back Mode
Each of these loop-back modes are described in
some detail below.
REMOTE LOOP-BACK (RLOOP) MODE
With Remote Loop-Back activated, (Channel Control
Register bit 2 = “1”) in Host Mode or in Hardware
Mode with LoopSEL (pin 58) tied Low and LoopEN
tied High received data after the jitter attenuator (if
selected) is looped back to the transmit path using
RxClk as transmit timing. In this mode the data/sig-
nals applied to the TxClk, TPOS/TDAT and TNEG in-
put pins are ignored, while RxClk and received data
will continue to be available at their respective output
pins. Simultaneously setting RLOOP and ALOOP ac-
tive is not allowed (see Loop-Back Mode in Figure 4 &
Figure 5). Remote loop-back has priority over TAOS.
DIGITAL LOCAL LOOP-BACK (DLOOP) MODE
The Digital Local Loop-Back mode allows the trans-
mit clock and data to be looped back to the corre-
sponding receiver output pins through the encoder/
decoder and the jitter attenuator. In this mode, the re-
ceive line signal is ignored, but the transmit data will
相關PDF資料
PDF描述
XRT83D10IW IC LIU T1/E1 SGL 28SOJ
XRT83L30IV-F IC LIU LH/SH T1/E1 SGL 64TQFP
XRT83L314IB-L IC LIU T1/E1/J1 14CH 304TBGA
XRT83L34IV-F IC LIU T1/E1/J1 QUAD 128TQFP
XRT83L38IB-F IC LIU T1/E1/J1 OCTAL 225BGA
相關代理商/技術參數
參數描述
XRT82L24ES 功能描述:界面開發工具 Evaluation Board for XRT82L24 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XRT82L24IV 制造商:EXAR 制造商全稱:EXAR 功能描述:QUAD E1 LINE TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT82L34IV 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Interface IC
XRT83D10 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE CHANNEL DS1/CEPT LINE INTERFACE UNIT
XRT83D10ES 功能描述:外圍驅動器與原件 - PCI 1 CHT1/E1LIUSH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray