NOTE
參數資料
型號： XRT75R12DIB-L
廠商： Exar Corporation
文件頁數： 17/133頁
文件大?。?/td> 0K
描述： IC LIU E3/DS3/STS-1 12CH 420TBGA
標準包裝： 40
類型： 線路接口裝置（LIU）
驅動器/接收器數： 12/12
規程： DS3，E3，STS-1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 420-LBGA 裸露焊盤
供應商設備封裝： 420-TBGA（35x35）
包裝： 托盤
XRT75R12D
109
REV. 1.0.3
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
NOTE: All of these intrinsic jitter measurements are to be performed using a band-pass filter of 10Hz to 400kHz.
Each of the scenarios presented in Table 43, are briefly described below.
8.5.1
DS3 De-Mapping Jitter
DS3 De-Mapping Jitter is the amount of Intrinsic Jitter that will be measured within the "Line" or "Facility-side"
DS3 signal, (after it has been de-mapped from a SONET signal) without the occurrence of "Pointer
Adjustments" within the SONET signal.
Telcordia GR-253-CORE requires that the "DS3 De-Mapping" Jitter be less than 0.4UI-pp, when measured
over all possible combinations of DS3 and STS-1 frequency offsets.
8.5.2
Single Pointer Adjustment
Telcordia GR-253-CORE states that if each pointer adjustment (within a continuous stream of pointer
adjustments) is separated from each other by a period of 30 seconds, or more; then they are sufficiently
isolated to be considered "Single-Pointer Adjustments".
Figure 55 presents an illustration of the "Single Pointer Adjustment" Scenario.
Telcordia GR-253-CORE states that the Intrinsic Jitter that is measured (within the DS3 signal) that is
ultimately de-mapped from a SONET signal that is experiencing "Single-Pointer Adjustment" events, must
NOT exceed the value 0.3UI-pp + Ao.
NOTES:
1.
Ao is the amount of Intrinsic Jitter that was measured during the "De-Mapping" Jitter portion of this test.
2.
Testing must be performed for both Incrementing and Decrementing Pointer Adjustments.
Continuous Pattern
A4
1.0UI-pp
Includes effects of Jitter from Clock-Gapping, De-Map-
ping and Pointer Adjustments.
Continuous Add
A5
1.3UI-pp
Includes effects of Jitter from Clock-Gapping, De-Map-
ping and Pointer Adjustments.
Continuous Cancel
A5
1.3UI-pp
Includes effects of Jitter from Clock-Gapping, De-Map-
ping and Pointer Adjustments.
FIGURE 55. ILLUSTRATION OF SINGLE POINTER ADJUSTMENT SCENARIO
TABLE 43: SUMMARY OF "CATEGORY I INTRINSIC JITTER REQUIREMENT PER TELCORDIA GR-253-CORE, FOR DS3
APPLICATIONS
SCENARIO
DESCRIPTION
SCENARIO
NUMBER
TELCORDIA GR-253-CORE
CATEGORY I INTRINSIC
JITTER REQUIREMENTS
COMMENTS
Initialization
Cool Down
Measurement Period
>30s
Pointer Adjustment Events
相關PDF資料
PDF描述
XRT75R12IB-L IC LIU E3/DS3/STS-1 12CH 420TBGA
XRT75VL00DIV IC LIU E3/DS3/STS-1 1CH 52TQFP
XRT75VL00IV-F IC LIU E3/DS3/STS-1 1CH 52TQFP
XRT79L71IB-F IC LIU/FRAMER DS3/E3 1CH 208BGA
XRT81L27IV-F IC LIU EI 7CH 3.3V 128TQFP
相關代理商/技術參數
參數描述
XRT75R12ES 功能描述:時鐘合成器/抖動清除器 12CH T3/E3/STS1LIUJA 3.3V W/REDUNDANCY RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75R12IB 功能描述:外圍驅動器與原件 - PCI 12CH E3/DS3/STS W/JITTER R3 TECH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75R12IB-F 功能描述:外圍驅動器與原件 - PCI 12 Channel 3.3V-5V temp -45 to 85C RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
XRT75R12IB-L 功能描述:LIN 收發器 Attenuator RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8
XRT75VL00 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*