- 您現在的位置：買賣IC網 > PDF目錄1977 > XRT75R12DIB-L (Exar Corporation)IC LIU E3/DS3/STS-1 12CH 420TBGA PDF資料下載
參數資料
| 型號： | XRT75R12DIB-L |
| 廠商： | Exar Corporation |
| 文件頁數： | 11/133頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU E3/DS3/STS-1 12CH 420TBGA |
| 標準包裝： | 40 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 12/12 |
| 規程： | DS3，E3，STS-1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 420-LBGA 裸露焊盤 |
| 供應商設備封裝： | 420-TBGA（35x35） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁
XRT75R12D
104
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
REV. 1.0.3
In the "Slip Buffer, the "input" STS-1 data (labeled "STS-1 Data_IN") is latched into the FIFO, upon a given
edge of the corresponding "STS-1 Clock_f1" input clock signal. The STS-1 Data (labeled "STS-1 Data_OUT")
is clocked out of the Slip Buffer upon a given edge of the "STS-1 Clock_f2" input clock signal.
The behavior of the data, passing through the "Slip Buffer" is now described for each possible relationship
between frequencies f1 and f2.
If f1 = f2
If both frequencies, f1 and f2 are exactly equal, then the STS-1 data will be "clocked" into the "Slip Buffer" at
exactly the same rate that it is "clocked out". In this case, the "Slip Buffer" will neither fill-up nor become
depleted. As a consequence, no pointer-adjustments will occur in this STS-1 data stream. In other words, the
STS-1 SPE will remain at a constant location (or offset) within each STS-1 envelope capacity for the duration
that this STS-1 signal is supporting this particular service.
If f1 < f2
If frequency f1 is less than f2, then this means that the STS-1 data is being "clocked out" of the "Slip Buffer" at
a faster rate than it is being clocked in.
In this case, the "Slip Buffer" will eventually become depleted.
Whenever this occurs, a typical strategy is to "stuff" (or insert) a "dummy byte" into the data stream. The
purpose of stuffing this "dummy byte" is to compensate for the frequency differences between f1 and f2, and
attempt to keep the "Slip Buffer, at a somewhat constant fill level.
NOTE: This "dummy byte" does not carry any valuable information (not for the user, nor for the system).
Since this "dummy byte" carries no useful information, it is important that the "Receiving PTE" be notified
anytime this "dummy byte" stuffing occurs. This way, the Receiving Terminal can "know" not to treat this
"dummy byte" as user data.
Byte-Stuffing and Pointer Incrementing in a SONET Network
Whenever this "byte-stuffing" occurs then the following other things occur within the STS-1 data stream.
During the STS-1 frame that contains the "Byte-Stuffing" event
a. The "stuff-byte" will be inserted into the byte position immediately after the H3 byte. This insertion of the
"dummy byte" immediately after the H3 byte position will cause the J1 byte (and in-turn, the rest of the
SPE) to be "byte-shifted" away from the H3 byte. As a consequence, the offset between the H3 byte posi-
tion and the STS-1 SPE will now have been increased by 1 byte.
FIGURE 51. AN ILLUSTRATION OF AN STS-1 SIGNAL BEING PROCESSED VIA A SLIP BUFFER
SLIP BUFFER
STS-1 Data_IN
STS-1 Clock_f1
STS-1 Data_OUT
STS-1 Clock_f2
Clock Domain operating
At frequency f1
Clock Domain operating
At Frequency f2.
相關PDF資料 |
PDF描述 |
|---|---|
| XRT75R12IB-L | IC LIU E3/DS3/STS-1 12CH 420TBGA |
| XRT75VL00DIV | IC LIU E3/DS3/STS-1 1CH 52TQFP |
| XRT75VL00IV-F | IC LIU E3/DS3/STS-1 1CH 52TQFP |
| XRT79L71IB-F | IC LIU/FRAMER DS3/E3 1CH 208BGA |
| XRT81L27IV-F | IC LIU EI 7CH 3.3V 128TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT75R12ES | 功能描述:時鐘合成器/抖動清除器 12CH T3/E3/STS1LIUJA 3.3V W/REDUNDANCY RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| XRT75R12IB | 功能描述:外圍驅動器與原件 - PCI 12CH E3/DS3/STS W/JITTER R3 TECH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT75R12IB-F | 功能描述:外圍驅動器與原件 - PCI 12 Channel 3.3V-5V temp -45 to 85C RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT75R12IB-L | 功能描述:LIN 收發器 Attenuator RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| XRT75VL00 | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
發布緊急采購，3分鐘左右您將得到回復。