REV. 1.0.2 TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO AND RS232 TRANSCEIVER PIN DESCRIPTIONS Pin Description N
參數資料
型號： XR20V2172L64-0A-EB
廠商： Exar Corporation
文件頁數： 23/51頁
文件大?。?/td> 0K
描述： EVAL BOARD FOR XR20V2170 64QFN
標準包裝： 1
系列： *
XR20V2172
3
REV. 1.0.2
TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO AND RS232 TRANSCEIVER
PIN DESCRIPTIONS
Pin Description
NAME
64-QFN
PIN #
TYPE
DESCRIPTION
I2C (SPI) INTERFACE
I2C/SPI#
61
I/O
I2C-bus or SPI interface select. I2C-bus interface is selected if this pin is
HIGH. SPI interface is selected if this pin is LOW. This pin is not 5V toler-
ant.
SDA
2
I/O
I2C-bus data input/output (open-drain). If SPI configuration is selected,
then this pin is undefined and must be connected to VCC. This pin is not
5V tolerant.
SCK
33
I
I2C-bus or SPI serial input clock.
When the I2C-bus interface is selected, the serial clock idles HIGH. When
the SPI interface is selected, the serial clock idles LOW. This pin is not 5V
tolerant.
A0/
CS#
57
I
I2C-bus device address select A0 or SPI chip select. If I2C-bus configura-
tion is selected, this pin along with the A1 pin allows user to change the
device’s base address. If SPI configuration is selected, this pin is the SPI
chip select pin (Schmitt-trigger, active LOW). This pin is not 5V tolerant.
A1/
SI
59
I
I2C-bus device address select A1 or SPI data input pin. If I2C-bus onfigu-
ration is selected, this pin along with A0 pin allows user to change the
device’s base address. If SPI configuration is selected, this pin is the SPI
data input pin. This pin is not 5V tolerant.
SO
64
O
SPI data output pin. If SPI configuration is selected then this pin is a
three-stateable output pin. If I2C-bus configuration is selected, this pin is
undefined and must be left unconnected.
IRQ#
38
OD
Interrupt output (open-drain, active LOW).
RESET#
52
I
Reset (active LOW) - A longer than 40 ns LOW pulse on this pin will reset
the internal registers and all outputs. The UART transmitter output will be
idle and the receiver input will be ignored. This pin is not 5V tolerant.
SERIAL I/O INTERFACE (CMOS/TTL Voltage Levels)
RXB
7
I
UART Channel B Receive Data. This pin can be used to communicate
with external IR or RS-232 transceiver. This pin is not 5V tolerant.
TXB
8
O
UART Channel B Transmit Data. This pin can be used to communicate
with external IR or RS-232 transceiver.
MODEM OR SERIAL I/O INTERFACE (EIA-232/RS-232 Voltage Levels)
RXDA
RXDB
39
29
I
UART Receive Data. UART receive data input must idle LOW (< 1.5V).
This input has an internal pull-down resistor and can be left unconnected
when not used.
TXDA
TXDB
42
27
O
UART Transmit Data. The TX signal will be LOW (< 1.5V) during reset or
idle (no data).
RTSA
RTSB
28
5
O
UART Request-to-Send. This output must be asserted prior to using auto
RTS flow control, see EFR[6], MCR[1] and IER[6].
CTSA
CTSB
63
4
I
UART Clear-to-Send. It can be used for auto CTS flow control, see
EFR[7], MSR[4] and IER[7]. This input has an internal pull-down resistor
and can be left unconnected when not used.
相關PDF資料
PDF描述
UPJ1C331MPD6TD CAP ALUM 330UF 16V 20% RADIAL
UUR0J471MNL1GS CAP ALUM 470UF 6.3V 20% SMD
XR20V2170L40-0B-EB EVAL BOARD FOR XR20V2170 40QFN
UPJ1K390MPD6TD CAP ALUM 39UF 80V 20% RADIAL
EEU-EB2E330 CAP ALUM 33UF 250V 20% RADIAL
相關代理商/技術參數
參數描述
XR20V2172L64-0B-EB 功能描述:UART 接口集成電路 Supports V2172 64pin QFN, SPI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR-210 制造商:EXAR 制造商全稱:EXAR 功能描述:FSK MODULATOR / DEMODULATOR
XR-2100CJ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MODEM
XR-2100CP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MODEM
XR-2103 制造商:EXAR 制造商全稱:EXAR 功能描述:FSK Modem Filter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*