- 您現在的位置：買賣IC網 > PDF目錄16527 > XR20V2172L64-0A-EB (Exar Corporation)EVAL BOARD FOR XR20V2170 64QFN PDF資料下載
參數資料
| 型號： | XR20V2172L64-0A-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 18/51頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR XR20V2170 64QFN |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
XR20V2172
25
REV. 1.0.2
TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO AND RS232 TRANSCEIVER
IER[4]: Sleep Mode Enable (requires EFR bit-4 = 1)
Logic 0 = Disable Sleep Mode (default).
Logic 1 = Enable Sleep Mode. See Sleep Mode section for further details.
IER[5]: Xoff Interrupt Enable (requires EFR bit-4=1)
Logic 0 = Disable the software flow control, receive Xoff interrupt (default).
Logic 1 = Enable the receive Xoff interrupt. See Software Flow Control section for details.
IER[6]: RTS# Output Interrupt Enable (requires EFR bit-4=1)
Logic 0 = Disable the RTS# interrupt (default).
Logic 1 = Enable the RTS# interrupt. The UART issues an interrupt when the RTS# pin makes a transition
from low to high.
IER[7]: CTS# Input Interrupt Enable (requires EFR bit-4=1)
Logic 0 = Disable the CTS# interrupt (default).
Logic 1 = Enable the CTS# interrupt. The UART issues an interrupt when CTS# pin makes a transition from
low to high.
4.4
Interrupt Status Register (ISR) - Read-Only
The UART provides multiple levels of prioritized interrupts to minimize external software interaction. The
Interrupt Status Register (ISR) provides the user with six interrupt status bits. Performing a read cycle on the
ISR will give the user the current highest pending interrupt level to be serviced, others are queued up to be
serviced next. No other interrupts are acknowledged until the pending interrupt is serviced. The Interrupt
Source Table, Table 9, shows the data values (bit 0-5) for the interrupt priority levels and the interrupt sources
associated with each of these interrupt levels.
4.4.1
Interrupt Generation:
LSR is by any of the LSR bits 1, 2, 3, 4 and 7.
RXRDY is by RX trigger level.
RXRDY Time-out is by a 4-char plus 12 bits delay timer.
TXRDY is by TX trigger level or TX FIFO empty.
MSR is by any of the MSR bits 0, 1, 2 and 3.
GPIO is when any of the GPIO inputs toggle.
Receive Xoff/Special character is by detection of a Xoff or Special character.
CTS# is when its transmitter toggles the input pin (from LOW to HIGH) during auto CTS flow control.
RTS# is when its receiver toggles the output pin (from LOW to HIGH) during auto RTS flow control.
4.4.2
Interrupt Clearing:
LSR interrupt is cleared by reading all characters with errors out of the RX FIFO.
RXRDY interrupt is cleared by reading data until FIFO falls below the trigger level.
RXRDY Time-out interrupt is cleared by reading RHR.
TXRDY interrupt is cleared by a read to the ISR register or writing to THR.
MSR interrupt is cleared by a read to the MSR register.
GPIO interrupt is cleared by reading the IOState register.
Xoff interrupt is cleared when Xon character(s) is received.
相關PDF資料 |
PDF描述 |
|---|---|
| UPJ1C331MPD6TD | CAP ALUM 330UF 16V 20% RADIAL |
| UUR0J471MNL1GS | CAP ALUM 470UF 6.3V 20% SMD |
| XR20V2170L40-0B-EB | EVAL BOARD FOR XR20V2170 40QFN |
| UPJ1K390MPD6TD | CAP ALUM 39UF 80V 20% RADIAL |
| EEU-EB2E330 | CAP ALUM 33UF 250V 20% RADIAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR20V2172L64-0B-EB | 功能描述:UART 接口集成電路 Supports V2172 64pin QFN, SPI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR-210 | 制造商:EXAR 制造商全稱:EXAR 功能描述:FSK MODULATOR / DEMODULATOR |
| XR-2100CJ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MODEM |
| XR-2100CP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MODEM |
| XR-2103 | 制造商:EXAR 制造商全稱:EXAR 功能描述:FSK Modem Filter |
發布緊急采購，3分鐘左右您將得到回復。