REV. 1.0.2 The V2172 UART portion stops its crystal oscillator to" />
參數資料
型號： XR20V2172L64-0A-EB
廠商： Exar Corporation
文件頁數： 10/51頁
文件大?。?/td> 0K
描述： EVAL BOARD FOR XR20V2170 64QFN
標準包裝： 1
系列： *
XR20V2172
18
TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO AND RS232 TRANSCEIVER
REV. 1.0.2
The V2172 UART portion stops its crystal oscillator to conserve power in this mode. The user can check the
XTAL2 pin for no clock output as an indication that the device has entered the partial sleep mode.
The UART portion in the V2172 resumes normal operation or active mode by any of the following:
■ a receive data start bit transition on the RXD input (LOW to HIGH)
■ a data byte is loaded to the transmitter, THR or FIFO
■ a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
If the UART portion of V2172 is awakened by any one of the above conditions, it will return to the sleep mode
automatically after all interrupting conditions have been serviced and cleared. If the UART portion of V2172 is
awakened by the modem inputs, a read to the MSR is required to reset the modem inputs. In any case, the
sleep mode will not be entered while an interrupt is pending. The UART portion of V2172 will stay in the sleep
mode of operation until it is disabled by setting IER bit-4 to a logic 0.
2.15.1.2
UART active, charge pump of RS-232 transceiver shut down
If the ACP pin is HIGH and the UART portion of the V2172 is not in sleep mode, then the charge pump will
automatically shut down to conserve power if the following conditions are true:
■ no activity on the TXD output signal
■ modem input signals (RX) are LOW
■ modem inputs have been idle for approximately 30 seconds
When these conditions are satisfied, the V2172 shuts down the charge pump and tri-states the RS-232 drivers
to conserve power. In this mode, the RS-232 receivers are fully active and the internal registers of the V2172
can be accessed. The time for the charge pump to resume normal operation after exiting the sleep mode is
typically 45
s. It will wake up by any of the following:
■ a receive data start bit transition on the RXD input (LOW to HIGH)
■ a data byte is loaded to the transmitter, THR or FIFO
■ a LOW to HIGH transition on any of the modem or general purpose serial inputs
Because the receivers are fully active when the charge pump is turned off, any data received will be transferred
to/from the UART without any issues.
2.15.2
Full Sleep Mode
In full sleep mode, the V2172 shuts down the charge pump and the internal oscillator. The V2172 enters the full
sleep mode if the following conditions are satisfied:
■ the UART portion of the V2172 is already in sleep mode (no output on XTAL2)
■ the ACP (Autosleep for Charge Pump) pin is HIGH
When these conditions are satisfied, both the UART and the charge pump will be in the sleep mode. In this
mode, the RS-232 receivers are fully active and the internal registers of the V2172 can be accessed. The
V2172 exits the full sleep mode if either the ACP pin becomes LOW or the internal oscillator starts up. The time
for the charge pump to resume normal operation after exiting the full sleep mode is typically 45
s.
If the serial clock, serial data, and modem input lines remain steady when the V2172 is in sleep mode, the
maximum current will be in the microamp range as specified in the DC Electrical Characteristics on page 39.
A word of caution: owing to the starting up delay of the crystal oscillator after waking up from sleep mode, the
first few receive characters may be lost. The number of characters lost during the restart also depends on your
operating data rate. More characters are lost when operating at higher data rate. Also, it is important to keep
RX input idling HIGH or “marking” condition during sleep mode to avoid receiving a “break” condition upon the
restart. This may occur when the external interface transceivers (RS-232, RS-485 or another type) are also put
to sleep mode and cannot maintain the “marking” condition. To avoid this, the designer can use a 47k-100k
ohm pull-up resistor on the RX input pin.
相關PDF資料
PDF描述
UPJ1C331MPD6TD CAP ALUM 330UF 16V 20% RADIAL
UUR0J471MNL1GS CAP ALUM 470UF 6.3V 20% SMD
XR20V2170L40-0B-EB EVAL BOARD FOR XR20V2170 40QFN
UPJ1K390MPD6TD CAP ALUM 39UF 80V 20% RADIAL
EEU-EB2E330 CAP ALUM 33UF 250V 20% RADIAL
相關代理商/技術參數
參數描述
XR20V2172L64-0B-EB 功能描述:UART 接口集成電路 Supports V2172 64pin QFN, SPI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR-210 制造商:EXAR 制造商全稱:EXAR 功能描述:FSK MODULATOR / DEMODULATOR
XR-2100CJ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MODEM
XR-2100CP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MODEM
XR-2103 制造商:EXAR 制造商全稱:EXAR 功能描述:FSK Modem Filter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*