- 您現在的位置：買賣IC網 > PDF目錄376440 > X40239 (Intersil Corporation) Triple Voltage Monitors, POR, 2 kbit EEPROM MEMORY, and Single/Dual DCP PDF資料下載
參數資料
| 型號： | X40239 |
| 廠商： | Intersil Corporation |
| 英文描述： | Triple Voltage Monitors, POR, 2 kbit EEPROM MEMORY, and Single/Dual DCP |
| 中文描述： | 三電壓監測器，葡萄牙，2千比特EEPROM存儲器，以及單/雙副處長 |
| 文件頁數： | 9/36頁 |
| 文件大小： | 541K |
| 代理商： | X40239 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
9
FN8115.0
April 11, 2005
Serial Start Condition
All commands are preceded by the START condition,
which is a HIGH to LOW transition of SDA while SCL
is HIGH. The device continuously monitors the SDA
and SCL lines for the START condition and does not
respond to any command until this condition has been
met. See Figure 2.
Serial Stop Condition
All communications must be terminated by a STOP
condition, which is a LOW to HIGH transition of SDA
while SCL is HIGH. The STOP condition is also used
to place the device into the Standby power mode after
a read sequence. A STOP condition can only be
issued after the transmitting device has released the
bus. See Figure 2.
Serial Acknowledge
An ACKNOWLEDGE (ACK) is a software convention
used to indicate a successful data transfer. The trans-
mitting device, either master or slave, will release the
bus after transmitting eight bits. During the ninth clock
cycle, the receiver will pull the SDA line LOW to
ACKNOWLEDGE that it received the eight bits of data.
Refer to Figure 3
The device will respond with an ACKNOWLEDGE
after recognition of a START condition if the correct
Device Identifier bits are contained in the Slave
Address Byte. If a write operation is selected, the
device will respond with an ACKNOWLEDGE after the
receipt of each subsequent eight bit word.
In the read mode, the device will transmit eight bits of
data, release the SDA line, then monitor the line for an
ACKNOWLEDGE. If an ACKNOWLEDGE is detected
and no STOP condition is generated by the master,
the device will continue to transmit data. The device
will terminate further data transmissions if an
ACKNOWLEDGE is not detected. The master must
then issue a STOP condition to place the device into a
known state.
DEVICE INTERNAL ADDRESSING
Addressing Protocol Overview
The user addressable internal components of the
X4023x can be split up into three main parts:
—One or Two Digitally Controlled Potentiometers
(DCPs)
—EEPROM array
—Control and Status (CR) Register
SCL
SDA
Start
Stop
Figure 2.
Valid Start and Stop Conditions
Data Output from
Transmitter
Data Output
from Receiver
8
1
9
Start
Acknowledge
Figure 3.
Acknowledge Response From Receiver
SCL from
Master
X40231, X40233, X40235, X40237, X40239
相關PDF資料 |
PDF描述 |
|---|---|
| X40420V14IZ-B | Dual Voltage Monitor with Intergrated CPU Supervisor |
| X40420S14IZ-A | Dual Voltage Monitor with Intergrated CPU Supervisor |
| X40420S14IZ-B | Dual Voltage Monitor with Intergrated CPU Supervisor |
| X40420S14Z-A | Dual Voltage Monitor with Intergrated CPU Supervisor |
| X40420S14Z-B | Dual Voltage Monitor with Intergrated CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X40239S16I-A | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40239S16I-AT1 | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40239S16I-B | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40239S16I-BT1 | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X-4028-P-C32-R | 功能描述:音頻指示器及警報器 2800Hz 105dBA 32Vdc RoHS:否 制造商:PUI Audio 產品:Indicators 聲壓級:85 dB 音調:Continuous 頻率:2300 Hz +/- 300 Hz 電壓額定值:5 VDC 電流額定值:30 mA 端接類型: 直徑:12 mm 安裝:Through Hole |
發布緊急采購，3分鐘左右您將得到回復。