參數資料
型號： X40239
廠商： Intersil Corporation
英文描述： Triple Voltage Monitors, POR, 2 kbit EEPROM MEMORY, and Single/Dual DCP
中文描述： 三電壓監測器，葡萄牙，2千比特EEPROM存儲器，以及單/雙副處長
文件頁數： 12/36頁
文件大?。?/td> 541K
代理商： X40239
12
FN8115.0
April 11, 2005
A nonvolatile write to a DCP will change the “wiper posi-
tion” by simultaneously writing new data to the associ-
ated WCR and NVM. Therefore, the new “wiper position”
setting is recalled into the WCR after V
CC
of the X4023x
is powered down and then powered back up.
A volatile write operation to a DCP however, changes
the “wiper position” by writing new data to the associ-
ated WCR only. The contents of the associated NVM
register remains unchanged. Therefore, when V
CC
to
the device is powered down then back up, the “wiper
position” reverts to that last position written to the DCP
using a nonvolatile write operation.
Both volatile and nonvolatile write operations are exe-
cuted using a three byte command sequence: (DCP)
Slave Address Byte, Instruction Byte, followed by a
Data Byte (See Figure 9)
A DCP Read operation allows the user to “read out”
the current “wiper position” of the DCP, as stored in
the associated WCR. This operation is executed using
the Random Address Read command sequence, con-
sisting of the (DCP) Slave Address Byte followed by
an Instruction Byte and the Slave Address Byte again
(Refer to Figure 10).
Instruction Byte
While the Slave Address Byte is used to select the
DCP devices, an Instruction Byte is used to determine
which DCP is being addressed.
The Instruction Byte (Figure 8) is valid only when the
Device Type Identifier and the Internal Device Address
bits of the Slave Address are set to 1010111. In this
case, the two Least Significant Bit’s (I1 - I0) of the
Instruction Byte are used to select the particular DCP
(0 - 2). In the case of a Write to any of the DCPs (i.e.
the LSB of the Slave Address is 0), the Most Signifi-
cant Bit of the Instruction Byte (I7), determines the
Write Type (WT) performed.
If WT is “1”, then a Nonvolatile Write to the DCP
occurs.
In this case, the “wiper position” of the DCP is changed
by simultaneously writing new data to the associated
WCR and NVM. Therefore, the new “wiper position”
setting is recalled into the WCR after V
CC
of the X4023x
has been powered down then powered back up.
If WT is “0” then a DCP Volatile Write is performed.
This operation changes the DCP “wiper position” by
writing new data to the associated WCR only. The
contents of the associated NVM register remains
unchanged. Therefore, when V
CC
to the device is
powered down then back up, the “wiper position”
reverts to that last written to the DCP using a nonvol-
atile write operation.
Figure 7.
DCP Power-up
t
V
CC
V
TRIP1
V
CC
(Max.)
t
PURST
Maximum Wiper Recall time
0
t
TRANS
WT
Description
0
Select a Volatile Write operation to be performed
on the DCP pointed to by bits P1 and P0
Select a Nonvolatile Write operation to be per-
formed on the DCP pointed to by bits P1 and P0
1
0
0
WT
0
0
0
P1
P0
WRITE TYPE
DCP SELECT
This bit has no effect when a Read operation is being performed.
I5
I6
I7
I4
I3
I2
I1
I0
Figure 8.
Instruction Byte Format
X40231, X40233, X40235, X40237, X40239
相關PDF資料
PDF描述
X40420V14IZ-B Dual Voltage Monitor with Intergrated CPU Supervisor
X40420S14IZ-A Dual Voltage Monitor with Intergrated CPU Supervisor
X40420S14IZ-B Dual Voltage Monitor with Intergrated CPU Supervisor
X40420S14Z-A Dual Voltage Monitor with Intergrated CPU Supervisor
X40420S14Z-B Dual Voltage Monitor with Intergrated CPU Supervisor
相關代理商/技術參數
參數描述
X40239S16I-A 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件
X40239S16I-AT1 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件
X40239S16I-B 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件
X40239S16I-BT1 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件
X-4028-P-C32-R 功能描述:音頻指示器及警報器 2800Hz 105dBA 32Vdc RoHS:否 制造商:PUI Audio 產品:Indicators 聲壓級:85 dB 音調:Continuous 頻率:2300 Hz +/- 300 Hz 電壓額定值:5 VDC 電流額定值:30 mA 端接類型: 直徑:12 mm 安裝:Through Hole
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*