- 您現在的位置：買賣IC網 > PDF目錄376440 > X40239 (Intersil Corporation) Triple Voltage Monitors, POR, 2 kbit EEPROM MEMORY, and Single/Dual DCP PDF資料下載
參數資料
| 型號： | X40239 |
| 廠商： | Intersil Corporation |
| 英文描述： | Triple Voltage Monitors, POR, 2 kbit EEPROM MEMORY, and Single/Dual DCP |
| 中文描述： | 三電壓監測器，葡萄牙，2千比特EEPROM存儲器，以及單/雙副處長 |
| 文件頁數： | 15/36頁 |
| 文件大?。?/td> | 541K |
| 代理商： | X40239 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
15
FN8115.0
April 11, 2005
EEPROM Byte Write
In order to perform an EEPROM Byte Write operation
to the EEPROM array, the Write Enable Latch (WEL)
bit of the CR Register must first be set (See “BL1, BL0:
Block Lock protection bits - (Nonvolatile)” on page 18.)
For a write operation, the X4023x requires the Slave
Address Byte and an Address Byte. This gives the
master access to any one of the words in the array.
After receipt of the Address Byte, the X4023x
responds with an ACKNOWLEDGE, and awaits the
next eight bits of data. After receiving the 8 bits of the
Data Byte, it again responds with an ACKNOWL-
EDGE. The master then terminates the transfer by
generating a STOP condition, at which time the
X4023x begins the internal write cycle to the nonvola-
tile memory (See Figure 11). During this internal write
cycle, the X4023x inputs are disabled, so it does not
respond to any requests from the master. The SDA
output is at high impedance. A write to a region of
EEPROM memory which has been protected with the
Block-Lock feature (See “BL1, BL0: Block Lock protec-
tion bits - (Nonvolatile)” on page 18.), suppresses the
ACKNOWLEDGE bit after the Address Byte.
EEPROM Page Write
In order to perform an EEPROM Page Write operation
to the EEPROM array, the Write Enable Latch (WEL)
bit of the CR Register must first be set (See “BL1, BL0:
Block Lock protection bits - (Nonvolatile)” on page 18.)
The X4023x is capable of a page write operation. It is
initiated in the same manner as the byte write opera-
tion; but instead of terminating the write cycle after the
first data byte is transferred, the master can transmit
an unlimited number of 8-bit bytes. After the receipt of
each byte, the X4023x responds with an ACKNOWL-
EDGE, and the address is internally incremented by
one. The page address remains constant. When the
counter reaches the end of the page, it “rolls over” and
goes back to ‘0’ on the same page.
For example, if the master writes 12 bytes to the page
starting at location 11 (decimal), the first 5 bytes are
written to locations 11 through 15, while the last 7
bytes are written to locations 0 through 6. Afterwards,
the address counter would point to location 7. If the
master supplies more than 16 bytes of data, then new
data overwrites the previous data, one byte at a time
(See Figure 13).
The master terminates the Data Byte loading by issu-
ing a STOP condition, which causes the X4023x to
begin the nonvolatile write cycle. As with the byte write
operation, all inputs are disabled until completion of
the internal write cycle. See Figure 12 for the address,
ACKNOWLEDGE, and data transfer sequence.
Stops and EEPROM Write Modes
Stop conditions that terminate write operations must
be sent by the master after sending at least 1 full data
byte and receiving the subsequent ACKNOWLEDGE
signal. If the master issues a STOP within a Data Byte,
or before the X4023x issues a corresponding
ACKNOWLEDGE, the X4023x cancels the write oper-
ation. Therefore, the contents of the EEPROM array
does not change.
EEPROM Array Read Operations
Read operations are initiated in the same manner as
write operations with the exception that the R/W bit of
the Slave Address Byte is set to one. There are three
basic read operations: Current EEPROM Address
Read, Random EEPROM Read, and Sequential
EEPROM Read.
S
t
a
r
t
S
t
o
p
Slave
Address
Address
Byte
Data
(n)
A
C
K
A
C
K
A
C
K
SDA Bus
Signals from
the Slave
Signals from
the Master
Data
(1)
A
C
K
(2 < n < 16)
Figure 12. EEPROM Page Write Operation
1 0 1 0 0 0 0 0
X40231, X40233, X40235, X40237, X40239
相關PDF資料 |
PDF描述 |
|---|---|
| X40420V14IZ-B | Dual Voltage Monitor with Intergrated CPU Supervisor |
| X40420S14IZ-A | Dual Voltage Monitor with Intergrated CPU Supervisor |
| X40420S14IZ-B | Dual Voltage Monitor with Intergrated CPU Supervisor |
| X40420S14Z-A | Dual Voltage Monitor with Intergrated CPU Supervisor |
| X40420S14Z-B | Dual Voltage Monitor with Intergrated CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X40239S16I-A | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40239S16I-AT1 | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40239S16I-B | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X40239S16I-BT1 | 功能描述:IC VOLTAGE MON TRPL EE 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:100 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:- 復位:低有效 復位超時:最小為 100 ms 電壓 - 閥值:4.38V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| X-4028-P-C32-R | 功能描述:音頻指示器及警報器 2800Hz 105dBA 32Vdc RoHS:否 制造商:PUI Audio 產品:Indicators 聲壓級:85 dB 音調:Continuous 頻率:2300 Hz +/- 300 Hz 電壓額定值:5 VDC 電流額定值:30 mA 端接類型: 直徑:12 mm 安裝:Through Hole |
發布緊急采購，3分鐘左右您將得到回復。