- 您現在的位置：買賣IC網 > PDF目錄245661 > W947D6HBHX5E (WINBOND ELECTRONICS CORP) 8M X 16 DDR DRAM, 5 ns, PBGA60 PDF資料下載
參數資料
| 型號： | W947D6HBHX5E |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | DRAM |
| 英文描述： | 8M X 16 DDR DRAM, 5 ns, PBGA60 |
| 封裝： | 8 X 9 MM, 0.80 MM PITCH, HALOGEN FREE AND LEAD FREE, VFBGA-60 |
| 文件頁數： | 2/60頁 |
| 文件大?。?/td> | 1160K |
| 代理商： | W947D6HBHX5E |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
W947D6HB / W947D2HB
128Mb Mobile LPDDR
Publication Release Date:Jun,17, 2011
- 10 -
Revision A01-003
6. FUNCTION DESCRIPTION
6.1 Initialization
LPDDR SDRAM must be powered up and initialized in a predefined manner. Operations procedures other than
those specified may result in undefined operation. If there is any interruption to the device power, the initialization
routine should be followed. The steps to be followed for device initialization are listed below.
The Mode Register and Extended Mode Register do not have default values. If they are not programmed during the
initialization sequence, it may lead to unspecified operation. The clock stop feature is not available until the device
has been properly initialized from Step 1 through 11.
Step 1: Provide power, the device core power (VDD) and the device I/O power (VDDQ) must be brought up
simultaneously to prevent device latch-up. Although not required, it is recommended that VDD and VDDQ
are from the same power source. Also Assert and hold Clock Enable (CKE) to a LVCMOS logic high level
Step 2: Once the system has established consistent device power and CKE is driven high, it is safe to apply
stable clock.
Step 3: There must be at least 200
μs of valid clocks before any command may be given to the DRAM. During this
time NOP or DESELECT commands must be issued on the command bus.
Step 4: Issue a PRECHARGE ALL command.
Step 5: Provide NOPs or DESELECT commands for at least tRP time.
Step 6: Issue an AUTO REFRESH command followed by NOPs or DESELECT command for at least tRFC time.
Issue the second AUTO REFRESH command followed by NOPs or DESELECT command for at least
tRFC time. Note as part of the initialization sequence there must be two Auto Refresh commands issued.
The typical flow is to issue them at Step 6, but they may also be issued between steps 10 and 11.
Step 7: Using the MRS command, program the base mode register. Set the desired operation modes.
Step 8: Provide NOPs or DESELECT commands for at least tMRD time.
Step 9: Using the MRS command, program the extended mode register for the desired operating modes. Note the
order of the base and extended mode register programmed is not important.
Step 10: Provide NOP or DESELECT commands for at least tMRD time.
Step 11: The DRAM has been properly initialized and is ready for any valid command.
相關PDF資料 |
PDF描述 |
|---|---|
| WS57C256F-70LMB | 32K X 8 UVPROM, 70 ns, CQCC32 |
| WMS128K8C-120FEIEA | 128K X 8 STANDARD SRAM, 120 ns, CDFP32 |
| WMS128K8L-100FEIE | 128K X 8 STANDARD SRAM, 100 ns, CDFP32 |
| WMS128K8L-120FECEA | 128K X 8 STANDARD SRAM, 120 ns, CDFP32 |
| WMS128K8L-120DRIEA | 128K X 8 STANDARD SRAM, 120 ns, CDSO32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W947D6HBHX5I | 制造商:WINBOND 制造商全稱:Winbond 功能描述:128Mb Mobile LPDDR |
| W947D6HBHX5I TR | 制造商:Winbond Electronics Corp 功能描述: |
| W947D6HBHX6E | 制造商:Winbond Electronics Corp 功能描述:IC LPDDR SDRAM 128MBIT 60VFBGA |
| W947D6HBHX6G | 制造商:WINBOND 制造商全稱:Winbond 功能描述:128Mb Mobile LPDDR |
| W948D2FB | 制造商:WINBOND 制造商全稱:Winbond 功能描述:256Mb Mobile LPDDR |
發布緊急采購，3分鐘左右您將得到回復。