參數資料
型號: W25Q80BVSSIG
廠商: WINBOND ELECTRONICS CORP
元件分類: PROM
英文描述: 8M X 1 SPI BUS SERIAL EEPROM, PDSO8
封裝: 0.208 INCH, GREEN, PLASTIC, SOIC-8
文件頁數: 5/75頁
文件大?。?/td> 1055K
代理商: W25Q80BVSSIG
W25Q80BV
Publication Release Date: October 06, 2010
- 13 -
Revision D
9.1.6
Complement Protect (CMP)
The Complement Protect bit (CMP) is a non-volatile read/write bit in the status register (S14). It is used in
conjunction with SEC, TB, BP2, BP1 and BP0 bits to provide more flexibility for the array protection. Once
CMP is set to 1, previous array protection set by SEC, TB, BP2, BP1 and BP0 will be reversed. For
instance, when CMP=0, a top 4KB sector can be protected while the rest of the array is not; when
CMP=1, the top 4KB sector will become unprotected while the rest of the array become read-only. Please
refer to the Status Register Memory Protection table for details. The default setting is CMP=0.
9.1.7
Status Register Protect (SRP1, SRP0)
The Status Register Protect bits (SRP1 and SRP0) are non-volatile read/write bits in the status register
(S8 and S7). The SRP bits control the method of write protection: software protection, hardware
protection, power supply lock-down or one time programmable (OTP) protection.
SRP1 SRP0
/WP
Status
Register
Description
0
X
Software
Protection
/WP pin has no control. The Status register can be written to
after a Write Enable instruction, WEL=1. [Factory Default]
0
1
0
Hardware
Protected
When /WP pin is low the Status Register locked and can not
be written to.
0
1
Hardware
Unprotected
When /WP pin is high the Status register is unlocked and can
be written to after a Write Enable instruction, WEL=1.
1
0
X
Power Supply
Lock-Down
Status Register is protected and can not be written to again
until the next power-down, power-up cycle.
(1)
1
X
One Time
Program
(2)
Status Register is permanently protected and can not be
written to.
Notes:
1. When SRP1, SRP0 = (1, 0), a power-down, power-up cycle will change SRP1, SRP0 to (0, 0) state.
2. This feature is available upon special order. Please contact Winbond for details.
9.1.8
Erase/Program Suspend Status (SUS)
The Suspend Status bit is a read only bit in the status register (S15) that is set to 1 after executing a
Erase/Program Suspend (75h) instruction. The SUS status bit is cleared to 0 by Erase/Program Resume
(7Ah) instruction as well as a power-down, power-up cycle.
9.1.9
Security Register Lock Bits (LB3, LB2, LB1)
The Security Register Lock Bits (LB3, LB2, LB1) are non-volatile One Time Program (OTP) bits in Status
Register (S13, S12, S11) that provide the write protect control and status to the Security Registers. The
default state of LB[3:1] is 0, Security Registers are unlocked. LB[3:1] can be set to 1 individually using the
Write Status Register instruction. LB[3:1] are One Time Programmable (OTP), once it’s set to 1, the
corresponding 256-Byte Security Register will become read-only permanently.
相關PDF資料
PDF描述
WED7G416IDE33ADC25 26M X 16 FLASH 3.3V PROM, DMA144
W3HG64M72EEU806PD4IGG 64M X 72 DDR DRAM MODULE, DMA200
W3EG7262S265D3 DDR DRAM MODULE, DMA184
W7NCF08GH10CS3JM1G FLASH 3.3V PROM MODULE, XMA50
W7NCF08GH10CSA8HM1G FLASH 3.3V PROM MODULE, XMA50
相關代理商/技術參數
參數描述
W25Q80BVSSIG TR 制造商:Winbond Electronics Corp 功能描述:SPIFLASH, 8M-BIT, 4KB UNIFORM 制造商:Winbond Electronics Corp 功能描述:IC FLASH 8MBIT 104MHZ 8SOIC
W25Q80BVSSIG/REELS 制造商:Winbond Electronics Corp 功能描述:
W25Q80BVSSIG-T 制造商:Winbond Electronics 功能描述:8MB SPI FLASH
W25Q80BVSSIP 制造商:WINBOND 制造商全稱:Winbond 功能描述:8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI
W25Q80BVZPAG 制造商:WINBOND 制造商全稱:Winbond 功能描述:8M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI