- 您現在的位置：買賣IC網 > PDF目錄225499 > V58C365164S5 (MOSEL-VITELIC) 4M X 16 DDR DRAM, 0.1 ns, PDSO66 PDF資料下載
參數資料
| 型號： | V58C365164S5 |
| 廠商： | MOSEL-VITELIC |
| 元件分類： | DRAM |
| 英文描述： | 4M X 16 DDR DRAM, 0.1 ns, PDSO66 |
| 封裝： | 0.400 INCH, PLASTIC, TSOP2-66 |
| 文件頁數： | 2/44頁 |
| 文件大?。?/td> | 507K |
| 代理商： | V58C365164S5 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
10
V58C365164S Rev. 1.5 November 2001
MOSEL VITELIC
V58C365164S
Output Data and Data Strobe Valid Window for DDR Read Cycles
Read Preamble and Postamble Operation
Prior to a burst of read data and given that the controller is not currently in burst read mode, the data strobe
signal (DQS), must transition from Hi-Z to a valid logic low. The is referred to as the data strobe “read pream-
ble” (tRPRE). This transition from Hi-Z to logic low nominally happens one clock cycle prior to the first edge of
valid data.
Once the burst of read data is concluded and given that no subsequent burst read operations are initiated,
the data strobe signal (DQS) transitions from a logic low level back to Hi-Z. This is referred to as the data
strobe “read postamble” (tRPST). This transition happens nominally one-half clock period after the last edge of
valid data.
Consecutive or “gapless” burst read operations are possible from the same DDR SDRAM device with no
requirement for a data strobe “read” preamble or postamble in between the groups of burst data. The data
strobe read preamble is required before the DDR device drives the first output data off chip. Similarly, the
data strobe postamble is initiated when the device stops driving DQ data at the termination of read burst cy-
cles.
D0
D1
(CAS Latency = 2; Burst Length = 2)
T0
T1
T2
T3
T4
READ
NOP
Command
DQS
DQ
tDV(min)
CK, CK
tDQSV(min)
相關PDF資料 |
PDF描述 |
|---|---|
| V608ME06 | VCO, 1900 MHz - 2270 MHz |
| V603ME07 | VCO, 1896 MHz - 1924 MHz |
| V6049001 | VCO, 1600 MHz - 2200 MHz |
| V610ME04 | VCO, 1950 MHz - 2150 MHz |
| V62/04634-01 | SPECIALTY ANALOG CIRCUIT, PDSO14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| V590ME01 | 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:LOW COST - HIGH PERFORMANCE VOLTAGE CONTROLLED OSCILLATOR |
| V590ME01-LF | 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:Voltage-Controlled Oscillator Surface Mount Module |
| V590ME01-LF_10 | 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:Voltage-Controlled Oscillator Surface Mount Module |
| V590ME08 | 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:VOLTAGE CONTROLLED OSCILLATOR |
| V590ME08-LF | 制造商:ZCOMM 制造商全稱:ZCOMM 功能描述:Voltage-Controlled Oscillator Surface Mount Module |
發布緊急采購，3分鐘左右您將得到回復。