- 您現在的位置：買賣IC網 > PDF目錄20614 > USB-EA-CONVZ (Analog Devices Inc)SUPPORT BOARD ADUC8XX PDF資料下載
參數資料
| 型號： | USB-EA-CONVZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 43/68頁 |
| 文件大?。?/td> | 0K |
| 描述： | SUPPORT BOARD ADUC8XX |
| 標準包裝： | 1 |
| 類型： | 仿真器 |
| 適用于相關產品： | ADuC8xx |
| 所含物品： | 模塊 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
REV. B
ADuC824
–48–
SERIAL PERIPHERAL INTERFACE
The ADuC824 integrates a complete hardware Serial Peripheral
Interface (SPI) interface on-chip. SPI is an industry standard syn-
chronous serial interface that allows eight bits of data to be
synchronously transmitted and received simultaneously, i.e., full
duplex. It should be noted that the SPI physical interface is shared
with the I
2C interface and therefore the user can only enable one
or the other interface at any given time (see SPE in SPICON
below). The system can be configured for Master or Slave operation
and typically consists of four pins, namely:
MISO (Master In, Slave Out Data I/O Pin), Pin#14
The MISO (master in slave out) pin is configured as an input line
in master mode and an output line in slave mode. The MISO
line on the master (data in) should be connected to the MISO
line in the slave device (data out). The data is transferred as
byte wide (8-bit) serial data, MSB first.
MOSI (Master Out, Slave In Pin), Pin#27
The MOSI (master out slave in) pin is configured as an output line
in master mode and an input line in slave mode. The MOSI
line on the master (data out) should be connected to the MOSI
line in the slave device (data in). The data is transferred as byte
wide (8-bit) serial data, MSB first.
SCLOCK (Serial Clock I/O Pin), Pin#26
The master clock (SCLOCK) is used to synchronize the data
being transmitted and received through the MOSI and MISO data
lines. A single data bit is transmitted and received in each SCLOCK
period. Therefore, a byte is transmitted/received after eight
SCLOCK periods. The SCLOCK pin is configured as an output
in master mode and as an input in slave mode. In master mode
the bit-rate, polarity and phase of the clock are controlled by
the CPOL, CPHA, SPR0 and SPR1 bits in the SPICON SFR
(see Table XIX). In slave mode the SPICON register will have
to be configured with the phase and polarity (CPHA and CPOL)
of the expected input clock. In both master and slave mode
the data is transmitted on one edge of the SCLOCK signal and
sampled on the other. It is important therefore that the CPHA
and CPOL are configured the same for the master and slave devices.
SS (Slave Select Input Pin), Pin#13
The Slave Select (
SS) input pin is only used when the ADuC824
is configured in slave mode to enable the SPI peripheral. This line
is active low. Data is only received or transmitted in slave mode
when the
SS pin is low, allowing the ADuC824 to be used in single
master, multislave SPI configurations. If CPHA = 1 then the
SS
input may be permanently pulled low. With CPHA = 0 then the
SS input must be driven low before the first bit in a byte wide
transmission or reception and return high again after the last bit
in that byte wide transmission or reception. In SPI Slave Mode,
the logic level on the external
SS pin (Pin# 13), can be read
via the SPR0 bit in the SPICON SFR.
The following SFR registers are used to control the SPI interface.
SPICON
SPI Control Register
SFR Address
F8H
Power-On Default Value
04H
Bit Addressable
Yes
I
P
S
IL
O
C
WE
P
SM
I
P
SL
O
P
CA
H
P
C1
R
P
S0
R
P
S
Table XIX. SPICON SFR Bit Designations
Bit
Name
Description
7
ISPI
SPI Interrupt Bit
Set by MicroConverter at the end of each SPI transfer.
Cleared directly by user code or indirectly by reading the SPIDAT SFR.
6
WCOL
Write Collision Error Bit
Set by MicroConverter if SPIDAT is written to while an SPI transfer is in progress.
Cleared by user code.
5
SPE
SPI Interface Enable Bit
Set by user to enable the SPI interface.
Cleared by user to enable the I
2C interface.
4
SPIM
SPI Master/Slave Mode Select Bit
Set by user to enable Master Mode operation (SCLOCK is an output).
Cleared by user to enable Slave Mode operation (SCLOCK is an input).
3
CPOL
*
Clock Polarity Select Bit
Set by user if SCLOCK idles high.
Cleared by user if SCLOCK idles low.
2
CPHA
*
Clock Phase Select Bit
Set by user if leading SCLOCK edge is to transmit data.
Cleared by user if trailing SCLOCK edge is to transmit data.
1
SPR1
SPI Bit-Rate Select Bits
0
SPR0
These bits select the SCLOCK rate (bit-rate) in Master Mode as follows:
SPR1
SPR0
Selected Bit Rate
SPR1
SPR0
Selected Bit Rate
00fCORE/2
10fCORE/8
01fCORE/4
11fCORE/16
In SPI Slave Mode, i.e., SPIM = 0, the logic level on the external
SS pin (Pin# 13), can be read via the SPR0 bit.
*Bits should contain the same values for master and slave devices.
相關PDF資料 |
PDF描述 |
|---|---|
| RGP10KE-E3/54 | DIODE GPP 1A 800V 500NS DO-41 |
| A7NXB-1506G | CABLE D-SUB - AMN15B/AE15G/X |
| C1005C0G1H470J | CAP CER 47PF 50V 5% NP0 0402 |
| SLF6045T-220M1R1-3PF | INDUCTOR POWER 22UH 1.1A SMD |
| GBM12DRTI-S13 | CONN EDGECARD 24POS .156 EXTEND |
相關代理商/技術參數 |
參數描述 |
|---|---|
| USB-ETH ADAPTER | 制造商:DANAHER - FLUKE 功能描述:USB TO 10/100MBPS ETHERNET ADAPTER |
| USB-ETHERNET-AX88772B | 制造商:Olimex 功能描述:USB ETH ADAPTOR OLINUXINO |
| USB-EVAL | 功能描述:界面開發工具 USB products evalua- tion board unpopultd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| USBEX02 | 制造商:Distributed By MCM 功能描述:15' USB 2.0 Active Extension Cable |
| USBEXT-150 | 制造商:DigitHead Inc 功能描述:USB EXTENDER 150' |
發布緊急采購，3分鐘左右您將得到回復。