- 您現在的位置：買賣IC網 > PDF目錄20614 > USB-EA-CONVZ (Analog Devices Inc)SUPPORT BOARD ADUC8XX PDF資料下載
參數資料
| 型號： | USB-EA-CONVZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 27/68頁 |
| 文件大小： | 0K |
| 描述： | SUPPORT BOARD ADUC8XX |
| 標準包裝： | 1 |
| 類型： | 仿真器 |
| 適用于相關產品： | ADuC8xx |
| 所含物品： | 模塊 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
REV. B
ADuC824
–33–
Table IX. Primary ADC, Typical Output RMS Noise ( V)
Typical Output RMS Noise vs. Input Range and Update Rate; Output RMS Noise in
V
SF
Data Update
Input Range
Word
Rate (Hz)
20 mV
40 mV
80 mV
160 mV
320 mV
640 mV
1.28 V
2.56 V
13
105.3
1.50
1.60
1.75
3.50
4.50
6.70
11.75
69
19.79
0.60
0.65
0.95
1.40
2.30
255
5.35
0.35
0.37
0.51
0.82
1.25
Table X. Primary ADC, Peak-to-Peak Resolution (Bits)
Peak-to-Peak Resolution vs. Input Range and Update Rate; Peak-to-Peak Resolution in Bits
SF
Data Update
Input Range
Word
Rate (Hz)
20 mV
40 mV
80 mV
160 mV
320 mV
640 mV
1.28 V
2.56 V
13
105.3
12
13
14
15
15.5
16
69
19.79
13
14
15
16
17
17.5
18
18.5
255
5.35
14
15
16
17
18
18.5
18.8
19.2
Table XI. Auxiliary ADC
Typical Output RMS Noise vs. Update Rate
*
Output RMS Noise in
V
SF
Data Update
Input Range
Word
Rate (Hz)
2.5 V
13
105.3
10.75
69
19.79
2.00
255
5.35
1.15
*ADC converting in bipolar mode.
Peak-to-Peak Resolution vs. Update Rate
1
Peak-to-Peak Resolution in Bits
SF
Data Update
Input Range
Word
Rate (Hz)
2.5 V
13
105.3
16
2
69
19.79
16
255
5.35
16
NOTES
1ADC converting in bipolar mode.
2In unipolar mode peak-to-peak resolution at 105 Hz is 15 bits.
Analog Input Channels
The primary ADC has four associated analog input pins (labelled
AIN1 to AIN4) that can be configured as two fully differential
input channels. Channel selection bits in the ADC0CON SFR
detailed in Table V allow three combinations of differential pair
selection as well as an additional shorted input option (AIN2–AIN2).
The auxiliary ADC has three external input pins (labelled AIN3
to AIN5) as well as an internal connection to the internal on-chip
temperature sensor. All inputs to the auxiliary ADC are single-
ended inputs referenced to the AGND on the part. Channel
selection bits in the ADC1CON SFR detailed previously in
Table VI allow selection of one of four inputs.
Two input multiplexers switch the selected input channel to the
on-chip buffer amplifier in the case of the primary ADC and
directly to the sigma-delta modulator input in the case of the
auxiliary ADC. When the analog input channel is switched, the
settling time of the part must elapse before a new valid word is
available from the ADC.
Primary and Auxiliary ADC Inputs
The output of the primary ADC multiplexer feeds into a high
impedance input stage of the buffer amplifier. As a result, the
primary ADC inputs can handle significant source impedances and
are tailored for direct connection to external resistive-type sensors
like strain gauges or Resistance Temperature Detectors (RTDs).
The auxiliary ADC, however, is unbuffered, resulting in higher
analog input current on the auxiliary ADC. It should be noted that
this unbuffered input path provides a dynamic load to the driving
source. Therefore, resistor/capacitor combinations on the input
pins can cause dc gain errors depending on the output impedance
of the source that is driving the ADC inputs.
Analog Input Ranges
The absolute input voltage range on the primary ADC is restricted
to between AGND + 100 mV to AVDD – 100 mV. Care must be
taken in setting up the common-mode voltage and input voltage
range so that these limits are not exceeded, otherwise there will
be a degradation in linearity performance.
PRIMARY AND AUXILIARY ADC NOISE PERFORMANCE
Tables IX, X, and XI below show the output rms noise in
V
and output peak-to-peak resolution in bits (rounded to the
nearest 0.5 LSB) for some typical output update rates on both
the Primary and Auxiliary ADCs. The numbers are typical and
are generated at a differential input voltage of 0 V. The output
update rate is selected via the SF7–SF0 bits in the Sinc Filter
(SF) SFR. It is important to note that the peak-to-peak resolu-
tion figures represent the resolution for which there will be no
code flicker within a six-sigma limit.
相關PDF資料 |
PDF描述 |
|---|---|
| RGP10KE-E3/54 | DIODE GPP 1A 800V 500NS DO-41 |
| A7NXB-1506G | CABLE D-SUB - AMN15B/AE15G/X |
| C1005C0G1H470J | CAP CER 47PF 50V 5% NP0 0402 |
| SLF6045T-220M1R1-3PF | INDUCTOR POWER 22UH 1.1A SMD |
| GBM12DRTI-S13 | CONN EDGECARD 24POS .156 EXTEND |
相關代理商/技術參數 |
參數描述 |
|---|---|
| USB-ETH ADAPTER | 制造商:DANAHER - FLUKE 功能描述:USB TO 10/100MBPS ETHERNET ADAPTER |
| USB-ETHERNET-AX88772B | 制造商:Olimex 功能描述:USB ETH ADAPTOR OLINUXINO |
| USB-EVAL | 功能描述:界面開發(fā)工具 USB products evalua- tion board unpopultd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| USBEX02 | 制造商:Distributed By MCM 功能描述:15' USB 2.0 Active Extension Cable |
| USBEXT-150 | 制造商:DigitHead Inc 功能描述:USB EXTENDER 150' |
發(fā)布緊急采購，3分鐘左右您將得到回復。