- 您現在的位置：買賣IC網 > PDF目錄20614 > USB-EA-CONVZ (Analog Devices Inc)SUPPORT BOARD ADUC8XX PDF資料下載
參數資料
| 型號： | USB-EA-CONVZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 41/68頁 |
| 文件大?。?/td> | 0K |
| 描述： | SUPPORT BOARD ADUC8XX |
| 標準包裝： | 1 |
| 類型： | 仿真器 |
| 適用于相關產品： | ADuC8xx |
| 所含物品： | 模塊 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
REV. B
ADuC824
–46–
WDCON
Watchdog Timer Control Register
SFR Address
C0H
Power-On Default Value
10H
Bit Addressable
Yes
3
E
R
P2
E
R
P1
E
R
P0
E
R
PR
I
D
WS
D
WE
D
WR
W
D
W
Table XVII. WDCON SFR Bit Designations
Bit
Name
Description
7
PRE3
Watchdog Timer Prescale Bits
6
PRE2
The Watchdog timeout period is given by the equation: tWD = (2
PRE
× (29/fPLL))
5
PRE1
(0
≤ PRE ≤ 7; f
PLL = 32.768 kHz)
4
PRE0
PRE3
PRE2
PRE1
PRE0 Timout Period (ms) Action
0
15.6
Reset or Interrupt
0
1
31.2
Reset or Interrupt
0
1
0
62.5
Reset or Interrupt
0
1
125
Reset or Interrupt
0
1
0
250
Reset or Interrupt
0
1
0
1
500
Reset or Interrupt
0
1
0
1000
Reset or Interrupt
0
1
2000
Reset or Interrupt
1
0
0.0
Immediate Reset
PRE3–0 > 1001
Reserved
3
WDIR
Watchdog Interrupt Response Enable Bit
If this bit is set by the user, the watchdog will generate an interrupt response instead of a system
reset when the watchdog timeout period has expired. This interrupt is not disabled by the CLR
EA instruction and it is also a fixed, high-priority interrupt. If the watchdog is not being used to
monitor the system, it can alternatively be used as a timer. The prescaler is used to set the timeout
period in which an interrupt will be generated. (See also Note 1, Table XXXIV in the Interrupt
System section.)
2
WDS
Watchdog Status Bit
Set by the Watchdog Controller to indicate that a watchdog timeout has occurred.
Cleared by writing a ‘0’ or by an external hardware reset. It is not cleared by a watchdog reset.
1
WDE
Watchdog Enable Bit
Set by user to enable the watchdog and clear its counters. If this bit is not set by the user within
the watchdog timeout period, the watchdog will generate a reset or interrupt, depending on WDIR.
Cleared under the following conditions, User writes ‘0,’ Watchdog Reset (WDIR = ‘0’); Hardware
Reset; PSM Interrupt.
0
WDWR
Watchdog Write Enable Bit
To write data into the WDCON SFR involves a double instruction sequence. The WDWR bit must
be set and the very next instruction must be a write instruction to the WDCON SFR.
e.g.,
CLR
EA
;
disable interrupts while writing
to WDT
SETB
WDWR
;
allow write to WDCON
MOV
WDCON, #72h
;
enable WDT for 2.0s timeout
SET B
EA
;
enable interrupts again (if rqd)
WATCHDOG TIMER
The purpose of the watchdog timer is to generate a device reset or
interrupt within a reasonable amount of time if the ADuC824
enters an erroneous state, possibly due to a programming error,
electrical noise, or RFI. The Watchdog function can be disabled by
clearing the WDE (Watchdog Enable) bit in the Watchdog Control
(WDCON) SFR. When enabled; the watchdog circuit will generate
a system reset or interrupt (WDS) if the user program fails to set
the watchdog (WDE) bit within a predetermined amount of time
(see PRE3–0 bits in WDCON). The watchdog timer itself is a
16-bit counter that is clocked at 32.768 kHz. The watchdog
time-out interval can be adjusted via the PRE3–0 bits in WDCON.
Full Control and Status of the watchdog timer function can be
controlled via the watchdog timer control SFR (WDCON). The
WDCON SFR can only be written by user software if the double
write sequence described in WDWR below is initiated on every
write access to the WDCON SFR.
相關PDF資料 |
PDF描述 |
|---|---|
| RGP10KE-E3/54 | DIODE GPP 1A 800V 500NS DO-41 |
| A7NXB-1506G | CABLE D-SUB - AMN15B/AE15G/X |
| C1005C0G1H470J | CAP CER 47PF 50V 5% NP0 0402 |
| SLF6045T-220M1R1-3PF | INDUCTOR POWER 22UH 1.1A SMD |
| GBM12DRTI-S13 | CONN EDGECARD 24POS .156 EXTEND |
相關代理商/技術參數 |
參數描述 |
|---|---|
| USB-ETH ADAPTER | 制造商:DANAHER - FLUKE 功能描述:USB TO 10/100MBPS ETHERNET ADAPTER |
| USB-ETHERNET-AX88772B | 制造商:Olimex 功能描述:USB ETH ADAPTOR OLINUXINO |
| USB-EVAL | 功能描述:界面開發工具 USB products evalua- tion board unpopultd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| USBEX02 | 制造商:Distributed By MCM 功能描述:15' USB 2.0 Active Extension Cable |
| USBEXT-150 | 制造商:DigitHead Inc 功能描述:USB EXTENDER 150' |
發布緊急采購，3分鐘左右您將得到回復。