參數資料
型號： USB-EA-CONVZ
廠商： Analog Devices Inc
文件頁數： 11/68頁
文件大?。?/td> 0K
描述： SUPPORT BOARD ADUC8XX
標準包裝： 1
類型： 仿真器
適用于相關產品： ADuC8xx
所含物品： 模塊
REV. B
ADuC824
–19–
PIN FUNCTION DESCRIPTIONS
Pin
No.
Mnemonic
Type
*
Description
1
P1.0/T2
I/O
Port 1.0 can function as a digital input or digital output and has a pull-up configuration as
described below for Port 3. P1.0 has an increased current drive sink capability of 10 mA and can
also be used to provide a clock input to Timer 2. When Enabled, Counter 2 is incremented in
response to a negative transition on the T2 input pin.
2
P1.1/T2EX
I/O
Port 1.1 can function as a digital input or digital output and has a pull-up configuration as
described below for Port 3. P1.1 has an increased current drive sink capability of 10 mA and
can also be used to provide a control input to Timer 2. When Enabled, a negative transition on
the T2EX input pin will cause a Timer 2 capture or reload event.
3
P1.2/DAC/IEXC1 I/O
Port 1.2. This pin has no digital output driver; it can function as a digital input for which ‘0’
must be written to the port bit. As a digital input, P1.2 must be driven high or low externally.
The voltage output from the DAC can also be configured to appear at this pin. If the DAC
output is not being used, one or both of the excitation current sources (200
A or 2 × 200 A)
can be programmed to be sourced at this pin.
4
P1.3/AIN5/IEXC2 I
Port 1.3. This pin has no digital output driver; it can function as a digital input for which ‘0’ must
be written to the port bit. As a digital input, P1.3 must be driven high or low externally. This
pin can provide an analog input (AIN5) to the auxiliary ADC and one or both of the excitation
current sources (200
A or 2 × 200 A) can be programmed to be sourced at this pin.
5AVDD
S
Analog Supply Voltage, 3 V or 5 V
6
AGND
S
Analog Ground. Ground reference pin for the analog circuitry
7
REFIN(–)
I
Reference Input, Negative Terminal
8
REFIN(+)
I
Reference Input, Positive Terminal
9–11
P1.4–P1.6
I
Port 1.4 to P1.6. These pins have no digital output drivers; they can function as digital inputs,
for which ‘0’ must be written to the respective port bit. As a digital input, these pins must be
driven high or low externally. These port pins also have the following analog functionality:
P1.4/AIN1
I
Primary ADC Channel, Positive Analog Input
P1.5/AIN2
I
Primary ADC Channel, Negative Analog Input
P1.6/AIN3
I
Auxiliary ADC Input or muxed Primary ADC Channel, Positive Analog Input
12
P1.7/AIN4/DAC I/O
Port 1.7. This pin has no digital output driver; it can function as a digital input for which ‘0’ must be
written to the port bit. As a digital input, P1.7 must be driven high or low externally. This pin can
provide an analog input (AIN4) to the auxiliary ADC or muxed Primary ADC Channel, Negative
Analog Input. The voltage output from the DAC can also be configured to appear at this pin.
13
SS
I
Slave Select Input for the SPI Interface. A weak pull-up is present on this pin.
14
MISO
I/O
Master Input/Slave Output for the SPI Interface. There is a weak pull-up on this input pin.
15
RESET
I
Reset Input. A high level on this pin for 24 core clock cycles while the oscillator is running resets
the device. There is a weak pull-down and a Schmitt trigger input stage on this pin. External
POR (power-on reset) circuitry must be added to drive the RESET pin as described later in
this data sheet.
16–19
P3.0–P3.3
I/O
P3.0–P3.3 are bidirectional port pins with internal pull-up resistors. Port 3 pins that have 1s written
to them are pulled high by the internal pull-up resistors, and in that state can be used as inputs.
As inputs, Port 3 pins being pulled externally low will source current because of the internal pull-up
resistors. When driving a 0-to-1 output transition, a strong pull-up is active for two core clock
periods of the instruction cycle. Port 3 pins also have various secondary functions described below.
P3.0/RXD
I/O
Receiver Data Input (asynchronous) or Data Input/Output (synchronous) of serial (UART) port.
P3.1/TXD
I/O
Transmitter Data Output (asynchronous) or Clock Output (synchronous) of serial (UART) port.
P3.2/
INT0
I/O
Interrupt 0, programmable edge or level triggered Interrupt input, which can be programmed
to one of two priority levels. This pin can also be used as a gate control input to Timer0.
P3.3/
INT1
I/O
Interrupt 1, programmable edge-or level-triggered Interrupt input, which can be programmed
to one of two priority levels. This pin can also be used as a gate control input to Timer1.
20, 34, 48
DVDD
S
Digital supply, 3 V or 5 V
21, 35, 47
DGND
S
Digital ground, ground reference point for the digital circuitry
相關PDF資料
PDF描述
RGP10KE-E3/54 DIODE GPP 1A 800V 500NS DO-41
A7NXB-1506G CABLE D-SUB - AMN15B/AE15G/X
C1005C0G1H470J CAP CER 47PF 50V 5% NP0 0402
SLF6045T-220M1R1-3PF INDUCTOR POWER 22UH 1.1A SMD
GBM12DRTI-S13 CONN EDGECARD 24POS .156 EXTEND
相關代理商/技術參數
參數描述
USB-ETH ADAPTER 制造商:DANAHER - FLUKE 功能描述:USB TO 10/100MBPS ETHERNET ADAPTER
USB-ETHERNET-AX88772B 制造商:Olimex 功能描述:USB ETH ADAPTOR OLINUXINO
USB-EVAL 功能描述:界面開發工具 USB products evalua- tion board unpopultd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
USBEX02 制造商:Distributed By MCM 功能描述:15' USB 2.0 Active Extension Cable
USBEXT-150 制造商:DigitHead Inc 功能描述:USB EXTENDER 150'
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*