參數資料
型號： UPD62AMC-XXX-5A4-A
元件分類： 微控制器/微處理器
英文描述： 4-BIT, MROM, 4 MHz, MICROCONTROLLER, PDSO20
封裝： 0.300 INCH, PLASTIC, SSOP-20
文件頁數： 16/62頁
文件大?。?/td> 272K
代理商： UPD62AMC-XXX-5A4-A
23
PD62A
Data Sheet U14474EJ2V0DS00
5.2 Standby Mode Setting and Release
The standby mode is set with the HALT #b3b2b1b0B instruction for both STOP mode and HALT mode. For the
standby mode to be set, the status flag (F) is required to have been cleared (to 0).
The standby mode is released by the release condition specified by the reset (RESET input, POC) or the HALT
instruction operand. If the standby mode is released, the status flag (F) is set (to 1).
Even when the HALT instruction is executed in a state in which the status flag (F) has been set (to 1), the standby
mode is not set. If the release condition is not met at this time, the status flag is cleared (to 0). If the release condition
is met, the status flag remains set (to 1).
Even in the case when the release condition has already been met at the point that the HALT instruction is
executed, the standby mode is not set. Here, also, the status flag (F) is set (to 1).
Caution Depending on the status of the status flag (F), the HALT instruction may not be executed. Be
careful about this. For example, when setting HALT mode after checking the key status with
the STTS instruction, because the system does not enter HALT mode as long as the status flag
(F) remains set (to 1), sometimes an unintended operation is performed. In this case, the
intended operation can be realized by executing the STTS instruction immediately after the
timer setting to clear (to 0) the status flag.
Example
STTS
#03H
;To check the KI pin status.
MOV
T, #0xxH
;To set the timer
STTS
#05H
;To clear the status flag
(During this time, be sure not to execute an instruction that may set the status flag.)
HALT
#05H
;To set HALT mode
Table 5-2. Addresses Executed After Standby Mode Release
Release Condition
Address Executed After Release
Reset
0 address
Release condition shown in Table 5-3
The address following the HALT instruction
…
相關PDF資料
PDF描述
UPD703201YGC-XXX-YEU-A 32-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP100
UPD703270GF-XXX-JBT 32-BIT, MROM, 20 MHz, RISC MICROCONTROLLER, PQFP100
UPD70F3008GJ-33-8EU 32-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQFP144
UPD70F3017AYF1-EA6-A 32-BIT, FLASH, 20 MHz, MICROCONTROLLER, PBGA121
UPD70F3015BGC-8EU-A 32-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
UPD62MC 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLER FOR INFRARED REMOTE CONTROL TRANSMISSION
UPD6300C 制造商:NEC 制造商全稱:NEC 功能描述:MOS DIGITAL INTEGRATED CIRCUIT
UPD6301 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ASIC
UPD6307 制造商:NEC 制造商全稱:NEC 功能描述:UPD6307 LCD ROW DRIVER
UPD6307G 制造商:NEC 制造商全稱:NEC 功能描述:UPD6307 LCD ROW DRIVER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*