- 您現在的位置：買賣IC網 > PDF目錄383876 > T7237A Compliance with the New ETSI PSD Requirement PDF資料下載
參數資料
| 型號： | T7237A |
| 英文描述： | Compliance with the New ETSI PSD Requirement |
| 中文描述： | 符合新的ETSI PSD的要求 |
| 文件頁數： | 76/116頁 |
| 文件大小： | 1056K |
| 代理商： | T7237A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁當前第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
Data Sheet
January 1998
T7256 Single-Chip NT1 (SCNT1) Transceiver
72
Lucent Technologies Inc.
Application Briefs
(continued)
Available Tools for Evaluation of the T7256
(continued)
Resetting SCNT1
The SPEC_V2 board has a push-button RESET switch
(S1) that may be used to RESET the 8751 microcon-
troller on the SPEC_V2. Asserting RESET will restart
the SPEC_V2 firmware. Upon power-on or RESET, the
SPEC_V2 displays the opening screen on the terminal,
and it appears as follows:
Lucent Technologies
SPEC_V2 Control Software, V 1.0, 6/2/96
(type "help" (lower case) for a list of commands)
At this point, any of the commands in Table 33 may be
entered.
If the current test mode is either single pulse or eye
pattern mode, the microcontroller will reset the SCNT1
when exiting that mode. This is necessary because the
only way to exit these test modes is by resetting
SCNT1 or cycling the power. The reset is accomplished
by pulling the SCNT1 RESET line (pin 43) low. Note
that this requires that any device on the UUT that
drives that RESET pin must have an open-drain or 3-
statable type of output. If RESET cannot be pulled low
due to device contention on the UUT, the UUT must be
powered down to get the SCNT1 out of test mode.
Notes on Single Pulse Mode
Note that, when a single pulse is output on the U-inter-
face, the following will be observed: approximately
25 ms after the rising edge of a single positive pulse, a
small positive glitch will occur. This is more pronounced
on +1 pulses than on +3 pulses, where it is hardly
detectable. The cause of the glitch is well understood
and was thoroughly investigated during the chip devel-
opment to ensure that it causes no harm under normal
operating conditions.
The explanation is as follows. The transmit sigma-delta
modulator in the SCNT1 is RESET whenever a transi-
tion from nonzero data to zero data occurs. It was
designed this way for ease of production testing, so
that the sigma-delta is always initialized to a known
state. This resetting is what causes the glitch. In normal
operation, the nonzero to zero case will never occur,
except when the transceiver is going from an active
state to RESET. In this case, there is a control signal
that grounds the input to the line driver to force it to
transmit 0 V (i.e., forces it into a low-impedance state—
this feature grew out of the ANSI requirements), so the
sigma-delta modulator has no effect in this case.
Thus, the glitch never occurs in normal operation and
should be ignored when observing the pulse output.
This has been confirmed independently at Bellcore
using their test bed that digitizes the chip output under
normal operation, and then reconstructs the pulse
shape using DSP filtering techniques.
相關PDF資料 |
PDF描述 |
|---|---|
| T7256A | Compliance with the New ETSI PSD Requirement |
| T7288 | CEPT/E1 Line Interface(CEPT/E1 線接口) |
| T7290A | DS1/T1/CEPT/E1 Line Interface(DS1/T1/CEPT/E1 線接口) |
| T7295-1 | E3 Integrated Line Receiver(E3 集成線接收器) |
| T7295-6 | DS3/SONET STS-1 Integrated Line Receiver(DS3/SONET STS-1 集成線接收器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T7240 | 制造商:TE Connectivity 功能描述: |
| T7-241A5 | 功能描述:撥動開關 ON NONE OFF 2 Pole Standard Bat Handle RoHS:否 制造商:OTTO 觸點形式: 開關功能: 電流額定值: 電壓額定值 AC: 電壓額定值 DC: 功率額定值: 端接類型: 安裝風格: 端子密封: 觸點電鍍: 照明: |
| T7-241B1 | 制造商:OTTO 功能描述:Toggle Switches ON NONE ON 2 Pole Standard Bat Handle 制造商:OTTO Engineering Inc 功能描述:Switch Toggle ON None ON DPDT Bat Toggle PC Pins 16A 115VAC 28VDC PC Mount with Threads |
| T7-241B5 | 功能描述:撥動開關 ON NONE ON 2 Pole Standard Bat Handle RoHS:否 制造商:OTTO 觸點形式: 開關功能: 電流額定值: 電壓額定值 AC: 電壓額定值 DC: 功率額定值: 端接類型: 安裝風格: 端子密封: 觸點電鍍: 照明: |
| T7-241C5 | 制造商:OTTO 功能描述:Toggle Switches (ON) NONE OFF 2 Pole Standard Bat Handle 制造商:OTTO Engineering Inc 功能描述:Switch Toggle (ON) None OFF DPST Bat Toggle PC Pins 16A 115VAC 28VDC PC Mount with Threads |
發布緊急采購，3分鐘左右您將得到回復。