參數資料
型號: T7237A
英文描述: Compliance with the New ETSI PSD Requirement
中文描述: 符合新的ETSI PSD的要求
文件頁數: 57/116頁
文件大?。?/td> 1056K
代理商: T7237A
Data Sheet
January 1998
T7256 Single-Chip NT1 (SCNT1) Transceiver
Lucent Technologies Inc.
53
Application Briefs
(continued)
T7256 Reference Circuit
(continued)
Power Status Leads
ANSI T1.601 Section 8.2.4 defines U-interface NT
power status bits ps1 and ps2. These bits are transmit-
ted across the U-Interface via the U maintenance chan-
nel. On the T7256, these bits are controlled by pins 8
and 9 (PS2E and PS1E). When the TDM highway is
used (NT1+ or TA modes), the ps1/ps2 bits are con-
trolled by internal registers that are written by an exter-
nal microprocessor. An NT1 typically has circuitry that
monitors the status of the power supply and sets ps1
and ps2 accordingly. In general, power status monitor-
ing circuitry is dependent on various system parame-
ters and requirements, and must be designed based on
the specific application’s requirements. For this reason,
there is no power status monitoring circuitry shown in
this design. Instead, pull-ups R1 and R2 in Figure 20
are provided to force a default indication of primary and
secondary power good status.
Fixed/Adaptive Timing Control
As detailed in Table 1, pin 7 of the T7256 controls
whether the S/T-interface will use fixed or adaptive tim-
ing recovery. When there is no connection to pin 7, an
internal 100K pull-up holds the pin high, which causes
the chip to default to adaptive timing recovery. JMP1 is
provided (see Figure 20) to change the timing recovery
mode to fixed timing by pulling pin 7 down through a
5.1 k
resistor.
相關PDF資料
PDF描述
T7256A Compliance with the New ETSI PSD Requirement
T7288 CEPT/E1 Line Interface(CEPT/E1 線接口)
T7290A DS1/T1/CEPT/E1 Line Interface(DS1/T1/CEPT/E1 線接口)
T7295-1 E3 Integrated Line Receiver(E3 集成線接收器)
T7295-6 DS3/SONET STS-1 Integrated Line Receiver(DS3/SONET STS-1 集成線接收器)
相關代理商/技術參數
參數描述
T7240 制造商:TE Connectivity 功能描述:
T7-241A5 功能描述:撥動開關 ON NONE OFF 2 Pole Standard Bat Handle RoHS:否 制造商:OTTO 觸點形式: 開關功能: 電流額定值: 電壓額定值 AC: 電壓額定值 DC: 功率額定值: 端接類型: 安裝風格: 端子密封: 觸點電鍍: 照明:
T7-241B1 制造商:OTTO 功能描述:Toggle Switches ON NONE ON 2 Pole Standard Bat Handle 制造商:OTTO Engineering Inc 功能描述:Switch Toggle ON None ON DPDT Bat Toggle PC Pins 16A 115VAC 28VDC PC Mount with Threads
T7-241B5 功能描述:撥動開關 ON NONE ON 2 Pole Standard Bat Handle RoHS:否 制造商:OTTO 觸點形式: 開關功能: 電流額定值: 電壓額定值 AC: 電壓額定值 DC: 功率額定值: 端接類型: 安裝風格: 端子密封: 觸點電鍍: 照明:
T7-241C5 制造商:OTTO 功能描述:Toggle Switches (ON) NONE OFF 2 Pole Standard Bat Handle 制造商:OTTO Engineering Inc 功能描述:Switch Toggle (ON) None OFF DPST Bat Toggle PC Pins 16A 115VAC 28VDC PC Mount with Threads