參數資料
型號： T7237A
英文描述： Compliance with the New ETSI PSD Requirement
中文描述： 符合新的ETSI PSD的要求
文件頁數： 27/116頁
文件大?。?/td> 1056K
代理商： T7237A
Data Sheet
January 1998
T7256 Single-Chip NT1 (SCNT1) Transceiver
Lucent Technologies Inc.
23
Microprocessor Interface Description
(continued)
Registers
(continued)
Table 6. Global Device Control—S/T-Interface (Address 02h)
Reg
GR2
Default State
on RESET
R/W
R/W
Bit 7
STOA
1
Bit 6
ACTSEL
ACTMODE/
INT pin
Bit 5
TDMEN
1
Bit 4
U2BDLN
1
Bit 3
SXE
1
Bit 2
SRESET
1
Bit 1
Bit 0
FT
1
SPWRUD
1
Register
GR2
Bit
0
Symbol
FT
Name/Description
Fixed/Adaptive Timing Control.
Controls mode of timing recovery on S/T-inter-
face if TDMEN = 0 (register GR2, bit 5). If TDMEN = 1, FT is ignored.
0—Fixed timing.
1—Adaptive timing (default).
S/T-Interface Powerdown Control.
When 0, this bit forces the S/T-interface to
remain in a powerdown mode. This is the same low-power mode the S/T-interface
is in when the T7256 is in its IDLE state with no activity on the U- or S/T-interfac-
es. In this mode, all S/T-interface circuits are powered down, except for circuits
required to detect an activation request from a TE.
0—Powerdown.
1—Normal (default).
S/T-Interface Reset.
While 0, this bit causes a reset of the S/T-interface, initial-
izing the interface in the same manner as the external RESET pin. Must be set to
1 for normal operation.
0—Reset.
1—Normal (default).
S/T-Interface D-Channel Echo Bit Control.
Controls data in E channel from NT
to TE on S/T-interface. This bit must be cleared during 2B+D loopbacks to meet
ITU-T I.430 requirements.
0—All 0s.
1—Echoes D channel from S/T receive path (default).
Nontransparent 2B+D Loopback Control.
When 0, this bit causes a nontrans-
parent loopback of 2B+D data from U receiver to U transmitter upstream of the
data flow matrix. Note that this loopback path is not as close to the S/T-interface
as the transparent loopback initiated by U2BDLT (register ECR0, bit 6). This loop-
back may be useful for test purposes. When this bit is set, the upstream data (NT
to LT direction) will be forced to all 1s until either ACTR = 1 (register CFR1, bit 0)
or XPCY = 0 (register GR1, bit 5).
0—2B+D loopback. All 1s 2B+D data is automatically generated towards the
TE.
1—No loopback (default).
TDM Bus Select.
Selects functions of pins 4, 7, 8, and 9.
0—TDM bus functions. Pins 4, 7, 8, and 9 configured as FS, TDMDI, TDMDO,
and TDMCLK, respectively. See DFR1 and TDR0 registers for TDM bus
programming details. Microprocessor register bits GR11, GR12, and GR20
control the PS2, PS1, and FT functions.
1—No TDM bus. Pins 4, 7, 8, and 9 configured as SYN8K/LBIND, FTE, PS2E,
and PS1E, respectively (default).
GR2
1
SPWRUD
GR2
2
SRESET
GR2
3
SXE
GR2
4
U2BDLN
GR2
5
TDMEN
相關PDF資料
PDF描述
T7256A Compliance with the New ETSI PSD Requirement
T7288 CEPT/E1 Line Interface(CEPT/E1 線接口)
T7290A DS1/T1/CEPT/E1 Line Interface(DS1/T1/CEPT/E1 線接口)
T7295-1 E3 Integrated Line Receiver(E3 集成線接收器)
T7295-6 DS3/SONET STS-1 Integrated Line Receiver(DS3/SONET STS-1 集成線接收器)
相關代理商/技術參數
參數描述
T7240 制造商:TE Connectivity 功能描述:
T7-241A5 功能描述:撥動開關 ON NONE OFF 2 Pole Standard Bat Handle RoHS:否 制造商:OTTO 觸點形式: 開關功能: 電流額定值: 電壓額定值 AC: 電壓額定值 DC: 功率額定值: 端接類型: 安裝風格: 端子密封: 觸點電鍍: 照明:
T7-241B1 制造商:OTTO 功能描述:Toggle Switches ON NONE ON 2 Pole Standard Bat Handle 制造商:OTTO Engineering Inc 功能描述:Switch Toggle ON None ON DPDT Bat Toggle PC Pins 16A 115VAC 28VDC PC Mount with Threads
T7-241B5 功能描述:撥動開關 ON NONE ON 2 Pole Standard Bat Handle RoHS:否 制造商:OTTO 觸點形式: 開關功能: 電流額定值: 電壓額定值 AC: 電壓額定值 DC: 功率額定值: 端接類型: 安裝風格: 端子密封: 觸點電鍍: 照明:
T7-241C5 制造商:OTTO 功能描述:Toggle Switches (ON) NONE OFF 2 Pole Standard Bat Handle 制造商:OTTO Engineering Inc 功能描述:Switch Toggle (ON) None OFF DPST Bat Toggle PC Pins 16A 115VAC 28VDC PC Mount with Threads
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*