- 您現在的位置：買賣IC網 > PDF目錄382551 > ST62T45B (意法半導體) The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each PDF資料下載
參數資料
| 型號： | ST62T45B |
| 廠商： | 意法半導體 |
| 元件分類： | DRAM |
| 英文描述： | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| 中文描述： | 該CAT24FC02是一個2 KB的EEPROM的國內256個8位每字舉辦的串行CMOS |
| 文件頁數： | 14/72頁 |
| 文件大?。?/td> | 514K |
| 代理商： | ST62T45B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
14/72
ST62T45B/E45B
MEMORY MAP
(Cont’d)
Additional Notes on Parallel Mode:
If the user wishes to perform parallel program-
ming, the first step should be to set the E2PAR2
bit. From this time on, the EEPROM will be ad-
dressed in write mode, the ROW address will be
latched and it will be possible to change it only at
the end of the programming cycle, or by resetting
E2PAR2 without programming the EEPROM. Af-
ter the ROW address is latched, the MCU can only
“see” the selected EEPROM row and any attempt
to write or read other rows will produce errors.
The EEPROM should not be read while E2PAR2
is set.
As soon as the E2PAR2 bit is set, the 8 volatile
ROW latches are cleared. From this moment on,
the user can load data in all or in part of the ROW.
Setting E2PAR1 will modify the EEPROM regis-
ters corresponding to the ROW latches accessed
after E2PAR2. For example, if the software sets
E2PAR2 and accesses the EEPROM by writing to
addresses 18h, 1Ah and 1Bh, and then sets
E2PAR1, these three registers will be modified si-
multaneously; the remaining bytes in the row will
be unaffected.
Note that E2PAR2 is internally reset at the end of
the programming cycle. This implies that the user
must set the E2PAR2 bit between two parallel pro-
gramming cycles. Note that if the user tries to set
E2PAR1 while E2PAR2 is not set, there will be no
programming cycle and the E2PAR1 bit will be un-
affected. Consequently, the E2PAR1 bit cannot be
set if E2ENA is low. The E2PAR1 bit can be set by
the user, only if the E2ENA and E2PAR2 bits are
also set.
EEPROM Control Register (EECTL)
Address: DFh
—
Reset status: 00h
Read/Write
Bit 7 =
D7
: Unused.
Bit6 =
E2OFF
:Stand-by Enable Bit.WRITE ONLY.
IfthisbitissettheEEPROMisdisabled (anyaccess
will be meaningless) andthepowerconsumption of
the EEPROM is reduced to its lowest value.
Bit 5-4 =
D5-D4
: Reserved.MUST be kept reset.
Bit 3 =
E2PAR1
: Parallel Start Bit.WRITE ONLY.
OnceinParallelMode,assoonastheusersoftware
sets the E2PAR1 bit, parallel writing of the 8 adja-
cent registers willstart. This bit is internally resetat
the end of the programming procedure. Note that
less than 8 bytes can be written if required, the un-
defined bytes being unaffected by the parallel pro-
gramming cycle; this is explained in greater detail
in the Additional Notes on Parallel Mode overleaf.
Bit 2 =
E2PAR2
: Parallel Mode En. Bit. WRITE
ONLY. This bit must be set by the user program in
order to perform parallel programming. If E2PAR2
is set and the parallel start bit (E2PAR1) is reset,
up to 8 adjacent bytes can be written simultane-
ously. These 8 adjacent bytes are considered as a
row, whose address lines A7, A6, A5, A4, A3 are
fixed while A2, A1 and A0 are the changing bits,
as illustrated inFigure 5. E2PAR2 is automatically
reset at the end of any parallel programming pro-
cedure. Itcan be reset by the user software before
starting the programming procedure, thus leaving
the EEPROM registers unchanged.
Bit 1 =
E2BUSY
: EEPROM Busy Bit.READ ON-
LY. This bit is automatically set by the EEPROM
control logic when the EEPROM is in program-
ming mode. The user program should test it be-
fore any EEPROM read or write operation; any at-
tempt to access the EEPROM while the busy bit is
set will be aborted and the writing procedure in
progress will be completed.
Bit 0 =
E2ENA
: EEPROM Enable Bit.WRITE ON-
LY. Thisbit enables programming of the EEPROM
cells. It must be set before any write to the EEP-
ROM register. Any attempt to write to the EEP-
ROM when E2ENA is low is meaningless and will
not trigger a write cycle.
Caution:
This register is undefined on reset. Nei-
ther read nor single bit instructions may be used to
address this register.
7
0
D7 E2OFF
D5
D4
E2PAR1 E2PAR2 E2BUSY E2ENA
13
相關PDF資料 |
PDF描述 |
|---|---|
| ST6245BQ6 | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| ST6263BB6 | 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, AUTO-RELOAD TIMER, EEPROM AND SPI |
| ST6260BM1 | 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, AUTO-RELOAD TIMER, EEPROM AND SPI |
| ST62E60B | 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, AUTO-RELOAD TIMER, EEPROM AND SPI |
| ST6260BB1 | 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER, AUTO-RELOAD TIMER, EEPROM AND SPI |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST62T45BQ6 | 功能描述:8位微控制器 -MCU OTP EPROM 8K RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ST62T45Q6 | 制造商:STMicroelectronics 功能描述:8BIT MCU - Bulk |
| ST62T46BB6 | 功能描述:8位微控制器 -MCU OTP EPROM 4K SPI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ST62T52CB6 | 功能描述:8位微控制器 -MCU OTP EPROM 2K No Intf RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| ST62T52CM3 | 制造商:STMicroelectronics 功能描述: 制造商:STMicroelectronics 功能描述:MCU 8BIT ST6 CISC 1836BYTE EPROM 5V 16SOIC - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。