參數資料
型號： ST16C554DIQ64TR-F
廠商： Exar Corporation
文件頁數： 15/39頁
文件大?。?/td> 0K
描述： IC UART FIFO 16B QUAD 64LQFP
標準包裝： 1,000
特點： *
通道數： 4，QUART
FIFO's： 16 字節
規程： RS232
電源電壓： 2.97 V ~ 5.5 V
帶自動流量控制功能： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 64-LQFP
供應商設備封裝： 64-LQFP（10x10）
包裝： 帶卷 (TR)
ST16C554/554D
22
2.97V TO 5.5V QUAD UART WITH 16-BYTE FIFO
REV. 4.0.1
MCR[3]: INT Output Enable
Enable or disable INT outputs to become active or in three-state. This function is associated with the INTSEL
input, see below table for details. This bit is also used to control the OP2# signal during internal loopback
mode. INTSEL pin must be LOW during 68 mode.
Logic 0 = INT (A-D) outputs disabled (three state) in the 16 mode (default). During internal loopback mode,
OP2# is HIGH.
Logic 1 = INT (A-D) outputs enabled (active) in the 16 mode. During internal loopback mode, OP2# is LOW.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and Figure 10.
MCR[7:5]: Reserved (Default 0)
4.8
Line Status Register (LSR) - Read/Write
This register is writeable but it is not recommended. The LSR provides the status of data transfers between the
UART and the host. If IER bit-2 is enabled, LSR bit-1 will generate an interrupt immediately and LSR bits 2-4
will generate an interrupt when a character with an error is in the RHR.
LSR[0]: Receive Data Ready Indicator
Logic 0 = No data in receive holding register or FIFO (default).
Logic 1 = Data has been received and can be read from the receive holding register or RX FIFO.
LSR[1]: Receiver Overrun Flag
Logic 0 = No overrun error (default).
Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens
when additional data arrives while the FIFO is full. In this case the previous data in the receive shift register
is overwritten. Note that under this condition the data byte in the receive shift register is not transferred into
the FIFO, therefore the data in the FIFO is not corrupted by the error.
LSR[2]: Receive Data Parity Error Tag
Logic 0 = No parity error (default).
Logic 1 = Parity error. The receive character in RHR does not have correct parity information and is suspect.
This error is associated with the character available for reading in RHR.
LSR[3]: Receive Data Framing Error Tag
Logic 0 = No framing error (default).
Logic 1 = Framing error. The receive character did not have a valid stop bit(s). This error is associated with
the character available for reading in RHR.
TABLE 12: INT OUTPUT MODES
INTSEL
PIN
MCR
BIT-3
INT A-D OUTPUTS IN 16 MODE
0
Three-State
0
1
Active
1
X
Active
相關PDF資料
PDF描述
ST16C580IQ48-F IC UART FIFO 16B 48TQFP
ST16C650AIJ44-F IC UART FIFO 32B 44PLCC
ST16C654DIQ64-F IC UART FIFO 64B QUAD 64LQFP
ST78C34CJ44-F IC UART FIFO 83B 44PLCC
ST78C36ACJ44-F IC UART FIFO 16B 44PLCC
相關代理商/技術參數
參數描述
ST16C554ECQ64 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC
ST16C554EDCJ68 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC
ST16C554EDCQ64 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC
ST16C554EDIJ68 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC
ST16C580 制造商:EXAR 制造商全稱:EXAR 功能描述:UART WITH 16-BYTE FIFO’s AND INFRARED (IrDA) ENCODER/DECODER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*